Safety Messages; Use As Directed; Storage And Disposal - SLV Elektronik AIXLIGHT PRO FRAMELESS Instrucciones De Servicio

ENGLISH
OPERATING MANUAL FOR
AIXLIGHT PRO FRAMELESS
Read this short manual carefully and keep it accessible for further
reference!

SAFETY MESSAGES

Disregard of the safety messages may lead to danger of life, burning or
fire!
• Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
• The product may not be modified or converted.
• Do not hang or fasten anything on the product, especially no decoration.
• Do not cover the product - provide free air circulation.
Additional safety messages are indicated by this symbol:

USE AS DIRECTED

This product serves exclusively lighting purposes and may:
• only be equipped with AIXLIGHT PRO modules.
• only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
• only be operated on normally or not flammable surfaces.
• only be used in dry condition,
• not in damp or dirt-endangered rooms.
• not in areas of high air humidity.
• not be exposed to strong mechanical loads or to strong contamination.

STORAGE AND DISPOSAL

Storage
• The product must be stored in a dry and clean environment. Do not
strain the product mechanically during storage.
After a damp or soiling storage the product may only be installed
after checking its condition by an approved electrician.
Disposal (European Union)
• Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive(WEEE,
2003/108) on electrical and electronic devices at local collection points for
such devices!
INSTALLATION
Unpacking
• Carefully take the product out of the packaging removing any transport
safeguards.
• Before disposal of the packaging material make sure that all components
of the product are removed.
Installation place
• The product is solely suited for recessed ceiling installation.
• Material thickness ceiling: 25mm max.
• Note the minimum distances in the ceiling. Minimum distance to each side: 5
cm.
Keep a sufficient distance to flammable surfaces. The indicated recess
depth is the minimum depth. Depending on the installation situation the needed
recess depth may be larger. This is especially the case, when there are
flammable materials above the luminaire or to ensure the sufficient ventilation
Do not cover the product, especially not with insulating materials:
Installation steps (read completely before installation)
• Mark and cut the opening. Do not damage the mains lead (fig. 1). The
measurements for the openings are:
115151 a: 19 / b: 19 / c: 23
115152 a: 35 / b: 19 / c: 23
.
115153 a: 50 / b: 19 / c: 23
115624 a: 19 / c: 14
115674 a: 19 / c: 20
115634 a: 36 / b: 19 / c: 14
115684 a: 36 / b: 19 / c: 20
• Slant the downside edges slightly (fig. 2).
• Only art.-no. 115621/24/71/74: Insert the installation frame into the opening.
Attach the punched plates. (fig. 3a).
• Prepare the installation frame (fig. 3b-5).
• Insert the installation frame into the opening. The four punched plates must
rest on the upper side of the ceiling material (fig. 6-7).
• Fix the installation frame from below through the above positioned punches
plates (fig. 8). Use screws that are adequate for the ceiling material.
• Adjust the height by the lateral screws inside. Use a level or an even metal
bar. The lower edges of the installation frame must be on the same level as
the lower edge of the ceiling (fig.9). Tighten the screws (fig. 10).
• Fill the cracks on the edges (fig.11). When the ceiling is painted, prime and
paint also the insides of the installation frame.
• Fig. 12 shows the ready painted installation frame.
• Fix the prepared module into the module housing by applying two lateral
screws (fig. 13).
• Establish the electrical connection according to the instruction manual of the
module.
• Insert the module housing with the installed module into the installation frame.
It is helpful to screw out the clamping plates so far that the housing can
pressed into the frame (fig.14). Tighten the screws after final adjustment until
the housing has a secure hold (fig.15).
• Equip now the module with reflector, bulb or accessory ( see the instruction
manual of the module).
Check if the product functions properly and is securely fixed!
art.-no. 115151/52/53 115624/34/74/84 © 07/2011 SLV Elektronik GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany, Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
.
.
b
a
c
a
b
a