Chicco I-Move Instrucciones De Uso página 23

kept away from the reach of children.
• Only use the correctly installed foot-
board when carrying babies of 15 months
and over. Do not exceed the weight limit
of 20 kg. (Accessory not included).
TIPS FOR CLEANING AND MAINTENANCE
This product requires periodic maintenance. The cleaning
and maintenance operations must only be carried out by
an adult.
CLEANING
The stroller has a removable lining (please refer to the "Re-
movable lining" section). Please refer to the care label for
instructions on cleaning the fabric parts. Please find below
the washing symbols and relative meanings:
Hand wash in cold water
Do not bleach
30° C
Do not tumble dry
Do not iron
Do not dry clean
Use a soft cloth to clean the plastic parts on a regular basis.
Always dry any metal parts that come into contact with
water to prevent the formation of rust.
MAINTENANCE
Lubricate the moving parts, if necessary, with a dry silicon
oil. Periodically check the condition of the wheels and keep
them clean of dust, dirt and sand. Make sure all plastic
parts that slide along the metal tubes are clean and free
from dust, dirt and sand; this will avoid friction that may
prevent the stroller from working properly. Keep the stroll-
er in a dry place.
OPENING THE STROLLER
WARNING: when opening the stroller, make sure that your
child and all other children are at a safe distance. Ensure
that during these operations the moving parts of the stroll-
er do not come into contact with your child.
1. Raise the handlebar until it locks in place (diag. 1).
2. Lift the frame until it reaches the position illustrated in
Diagram 2.
3. Press the open/close lever (A) following the instructions
below: move it to the left (1) and then upwards (2) as seen
in diagram 3.
4. Push the rear leg outwards until it reaches the lock posi-
tion (diagram 4).
WARNING: make sure the Stroller is locked in the open
position.
5. Release the snap-clasps on the handle (diagram 5A) and
move the handlebar to the position illustrated in diagram
5B.
FITTING AND REMOVING THE WHEELS
6. Insert the wheel pin into the hole on the rear leg tube,
as illustrated in diagram 6. Repeat the operation for both
wheels.
7. The rear wheels can be removed. Press the button in the
centre of the wheel and slide it off the pin (diagram 7).
FITTING THE SEAT
8. To assemble the seat onto the stroller frame, grasp both
sides of the seat with two hands and connect the base to
the frame (diagrams 8A and 8B) so that the groove on the
seat (A) is aligned with the arrows on the frame (B) (dia-
gram 8C). Adjust the position of the seat until it clicks se-
curely into place.
SAFETY HARNESS
The stroller comes with a five-point safety harness which
consists in two shoulder straps, a lap belt and a crotch
strap with a buckle.
WARNING: For use with children from birth up to approxi-
mately 6 months of age, it is necessary to use the shoulder
straps, sliding them first through the two adjustment holes.
9. Thread the safety clasps through the fabric loops (diag.
9) and check that the shoulder straps are fitted at the right
height for the child: if this is not the case, adjust the height
as necessary.
10. Bring the upper harness strap clasp (A) in line with the
triangle on the lap belt clasp (B) (Diagram 10) and then in-
sert them both in the harness buckle (C). Slide the harness
straps along the plastic rings until they are tight enough.
Press the centre button (D) to release the safety harness
straps.
WARNING: the safety harness must always be fastened to
guarantee complete safety for your child.
WARNING: After removal of the safety harness (e.g. for
washing), ensure that the harness is reassembled correctly
using the anchorage points. The harness must be re adjust-
ed. The rings are positioned at the back of the stroller on
the right and left side. The waist belt must be repositioned
by introducing the edges in the relative rings (fig. 10B).
PARKING BRAKE
The parking brake control lever is fitted on the stroller han-
dlebar,
11. To activate the brake, turn the lever counter clockwise
until it locks in place, and the red brake ON indicator is vis-
ible. The braking device is now fully operational (Diagram
11).
12. To release the brakes, press the central button on the
lever (diagram 12). The green brake OFF indicator will now
be visible.
WARNING: Always apply the brakes whenever the stroller
is stationary. Never leave the stroller on a sloping surface
with a child inside, even with the parking brake ON.
USER MODES
13. The stroller can be used in either parent-facing or front-
facing mode.
The stroller can be switched from one user mode to an-
other by:
- rotating the seat (diag. 13A front-facing, diag. 13B parent-
facing)
- inverting the handlebar (diag. 13C front-facing, diag. 13D
parent-facing)
ROTATING THE SEAT
WARNING: When performing the operations illustrated
below, always place the stroller on a flat even surface and
remove any weights attached to the handlebar to avoid
compromising its stability.
To switch from parent-facing mode to front-facing mode,
or vice-versa, apply the brakes and proceed as follows:
14. Release both snap-clasps on the handle simultaneously,
and move the hand grip section upwards, as seen in dia-
gram 14.
15. Use your foot to release the rotation lock pedal as seen
in diagram 15.
23