Poulan Pro PP28RJ Manual De Instrucciones página 10

BEFORE STARTING ENGINE
WARNING:
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call customer
support.
FUELING ENGINE
WARNING:
when refueling.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 2.6 ounces of
2- - cycle synthetic oil into
one gallon of fresh gas.
IMPORTANT:
This equipment is designed to
operate on unleaded gasoline with a minimum
87 octane (R+M/2 method), with ethanol blen-
ded up to 10% maximum by volume (E-10). Be-
fore operation, gasoline must be mixed with a
good quality synthetic 2-cycle air-cooled engine
oil designed to be mixed at a ratio of 50:1. Mix
gasoline and oil at a ratio of 50:1. A 50:1 ratio is
obtained by mixing 2.6 fluid ounces of oil with 1
gallon of unleaded gasoline. DO NOT USE
automotive oil or marine oil. These oils will
cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is ad-
ded to gasoline, shake container momentarily to
assure that the fuel is thoroughly mixed. Always
read and follow the safety rules relating to fuel
before fueling your unit. Purchase fuel in quantit-
ies that can be used within 30 days to assure
fuel freshness.
CAUTION:
Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty. Do not
use alternate fuels such as ethanol blends
above 10% by volume (E-15, E-85) or any
methanol blended fuel. Use of these fuels can
cause major engine performance and durability
problems.
HOW TO STOP YOUR UNIT
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch. The switch will automatically return to
the ON position. Wait 5 seconds before at-
tempting to restart unit to allow switch to reset.
ON/STOP
switch
HOW TO START YOUR UNIT
WARNING:
muffler. A hot muffler can cause serious burns.
Be sure to read the fuel
Remove fuel cap slowly
Avoid any contact with the
If your engine still does not
start after following these
instructions, please call
customer support.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move start lever to the START position.
4. Pull starter rope handle sharply 5 times. If
the temperature is above 90°F (32°C),
pull 3 times.
5. Squeeze and hold trigger.
6. Pull starter rope handle until engine
starts.
If the engine does not start, it is probably
flooded. Proceed to STARTING A FLOODED
ENGINE.
STARTING A WARM ENGINE
1. Squeeze and hold trigger.
2. Pull starter rope handle until engine starts.
If the engine does not start, it is probably
flooded. Proceed to STARTING A FLOODED
ENGINE.
STARTING A FLOODED ENGINE
1. Squeeze and hold trigger.
2. Pull starter rope handle until engine starts.
If the unit still does not start, refer to
TROUBLESHOOTING TABLE or call cus-
tomer support.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
Edger . . . . . . . . . . . . . . . . . . . .
Cultivator . . . . . . . . . . . . . . . . .
Blower . . . . . . . . . . . . . . . . . . .
Brushcutter . . . . . . . . . . . . . . .
Pruner . . . . . . . . . . . . . . . . . . .
Pruner . . . . . . . . . . . . . . . . . . .
Hedge Trimmer . . . . . . . . . . . .
WARNING:
connect spark plug before removing or instal-
ling attachments.
10
Starting Position
HELPFUL TIP
Starter handle
Primer bulb
Start lever
MODEL:
PP1000E
PP2000T
PP3000B
PP4000C
PP5000P
PP5500P
PP6000H
Always stop unit and dis-