Cleaning And Storage - JOCCA 6163 Manual De Instrucciones

EN-12
-Before connecting the appliance to the mains, check that the cable and plug are in
perfect conditions. Also check that the voltage indicated on the appliance is valid for
your electrical installation. Plug into a socket with an earthing connection.
-If you detect that the power supply cable or the plug are damaged, do not use the
appliance or try to replace the cable yourself. Go directly to the authorised JOCCA
technical service where they will replace it correctly for you.
-Do not immerse the appliance or any part of it in water or any other liquid.
-To avoid overheating, it is advisable to unroll completely the power cable and to
disconnect the plug from the mains when the appliance is not in use.
-If for any reason you feel that the heat provided by a device is excessive, move away
your body from a mattress immediately.
-Do not pull the cable to unplug the appliance from the mains, always pull from the
plug.
-For your safety and for the appliance to work correctly, always use JOCCA spare
parts and accessories.
-Always unplug a device from electrical network when finish it using, before its cleaning
and if it does not work correctly.
-Do not use a device if it is wet; do not leave a device under the exposure of weathering
such as rain, sun, snow etc.
-Do not insert pins into a mattress
-Do not use a product if it is wrinkled or folded.
-A prolonged use with maximum level of regulation can lead to burns on the skin.
Never sleep on an operating mattress.
-Check a device frequently for signs of wear or damage. If such signs exist or a device
has been used improperly, consult a distributor before any further use.
-Do not use a device neither with wet or sweat body nor with wet feet or hands.
INSTRUCTIONS FOR USE
-The device has a security system that switches off it in 15 minutes of continuous
operation.
-First of all before you plug in a device check if it is in perfect condition.
-Connect the incorporated adaptor CA/CC (Fig. F) to a remote control and connect
another end of the adaptor to an electricity network as it is shown on the figure.
-Then connect a remote control to a mattress, making sure the pins match the holes.
-Place a massage mattress where you wish to use it and make yourself comfortable on
it.
-Take a remote control and press the button I/O, a pad will be activated automatically
and a pilot light will be switched on indicating that a device is in operation.
-A mattress has 5 massage programs and 3 intensity levels that can be chosen by a
remote control.
-Pressing the button MODE (F1-F5) you can select a massage program from 1 to 5
passing through F1, F2, F3, F4 and F5.
-When a massage program has been selected, it is possible increase its intensity up to
3 times more pressing the button
I: low intensity
II: medium intensity
III: high intensity
-Besides you can select a zone you wish to massage: neck, lower back, the back and
legs, selecting each zone by a remote control. You just have to press a button of each
zone and it will be activated. A pilot light will indicate you a selected massage zone.
-Finally press a button to activate the heating function a pilot light will be switched
on. Press the same button to deactivate it.
-To disconnect a massage function it is enough to press again the button I/O.
-A device will not be switched off till you unplug it completely from the electricity network.

CLEANING AND STORAGE

-Before cleaning the appliance, make sure it has been disconnected from the mains.
-Do not use abrasive detergents or products that may damage the appliance.
-Clean a device with dry cloth to remove any dust rests or dirt.
-Use dry cloth to clean a remote control.
-Place a device at a clean and dry place.
TECHNICAL SPECIFICATIONS
CHARGER: 100-240V ~ 50/60hz 0.5A
12V DC 1,2A
This device conforms to the safety requirements and provisions of directives 2006/95/
EC on Low tension devices and 2004/108/EC on Electromagnetic Compatibility.
PRODUCT RECYCLING - ENVIRONMENT
Packaging
The materials used in this product's packaging are integrated in a
system of waste collection, sorting and recycling. If you wish to
dispose of these materials, you should use rubbish bins or other
municipal means of waste collection that are appropriate for each
type of material.
Electrical and Electronic Product
This symbol means that if you wish to dispose of this product at the
end of its life, you must take it to a waste collection company
authorized for the selective collection of Waste Electronic and
Electrical Equipment (WEEE).
This product does not contain concentrations of materials
considered harmful to the environment.
:
EN-13