Taurus Ikarus Manual De Uso página 14

hair (Fig. 4). In some cases it's necessary to go over
what you have done a second time from front to back.
- The comb guide size 18-3 mm (E) is for when you want
to achieve a more precise cut.
- Use comb guides size 36-21 mm (F) to leave hair at
a longer length. Hold the hair up with the comb or the
comb and your fingers and cut.
- Always work from the back to the front reducing the
length between your fingers or the comb and the head
gradually.
Step 5. Final touch
- Finally use the appliance without attaching any comb
guides to the blades to cut the hair around the base of
the neck, the sides of the neck and the ears. For a closer
trim, use the blade adjustment knob (G) in position 1 for
1.8 mm or 2 for 0.8 mm
- To make the sideburns straight, turn the appliance over
to use the upper blades (Fig. 5). Move the appliance
adapting it the physiognomy of the head.
Thinning out function:
- The appliance includes a thinning out function, which
reduces the volume of hair. Select this function to use or
hide the thinning out comb (Fig. 6)
Beard trimming comb:
- You can use the 18-3 mm comb to trim to 3 mm, or you
can just adjust the cut with the blade adjustment knob
(G), which will allow you a cut of 1.8 mm in position 1 or
0.8 mm in position 2.
Once you have finished using the appliance:
- Turn the appliance off, using the on/off switch.
- Clean the appliance
Cleaning
- Disconnect the appliance from the mains and let it cool
before undertaking any cleaning task.
- Dismantle the appliance following these steps:
Remove the thinning out comb by using the thinning out
comb switch (I)
Hold the appliance with one hand and use the thumb to
press the blades while holding the plastic part with the
index finger until the blades come out (Fig. 7).
- Use the cleaning brush (O) to remove the hair from
inside the appliance and the blades.
- Clean the equipment using a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning the
appliance.
- Do not submerge the appliance in water or any other
liquid, or place it under a running tap.
- During the cleaning process, take special care with the
blades, as they are very sharp.
Anomalies and repair
Take the appliance to an authorised technical support
service if problems arise.
Manual Ikarus/Ikarus premium.indb 14
If the connection to the mains has been damaged, it
must be replaced and you should proceed as you would
in the case of damage.
For EU product versions and/or in case that it is reques-
ted in your country:20111124~115126
Ecology and recyclability of the product
- The materials of which the packaging of this appliance
consists are included in a collection, classification and
recycling system. Should you wish to dispose of them,
use the appropriate public containers for each type of
material.
- The product does not contain concentrations of
substances that could be considered harmful to the
environment
- Remember that one should abide by the regulations
concerning the elimination of this type of contaminant.
This symbol means that in case you wish to
dispose of the product once its working life has
ended, take it to an authorised waste agent for
the selective collection of waste electrical and
electronic equipment (WEEE)
This symbol means that the product may
include a battery or batteries; the user must
remove them before disposing of the product.
Remember that batteries must be disposed of
in duly authorised containers. Do not dispose of them in
fire.
How to remove the batteries from the interior of the
device:
The battery must be removed from the appliance before
it is scraped
Caution: It is important that the batteries are fully dis-
charged prior to its withdrawal from the apparatus.
The appliance must be disconnected from the supply
mains when removing the battery.
To remove the batteries, once the life of the applian-
ce, proceed as follows:
- Open the top shell of the appliance, removing pre-
viously with the help of a screwdriver fixing screws (Fig.
8)
- Identify the battery wires and cut their (Red and Black).
To avoid risks of a short circuit with a possible residual
battery load, first cut the Red wire and protect it by using
insulating tape, then proceed to cut the Black wire proce-
eding in the same way. (Fig. 9)
- Safely remove the battery from its housing.
This appliance complies with Directive 2006/95/EC on
Low Voltage, Directive 2004/108/EC on Electromagnetic
Compatibility, Directive 2011/65/EC on the restrictions of
the use of certain hazardous substances in electrical and
electronic equipment and Directive 2009/125/EC on the
ecodesign requirements for energy-related products.
27/11/15 10:48