Black+Decker KC4815 Manual De Instrucciones página 16

16 • ENGLISH
device such as a torque wrench should be used when
under tightened or over tightened fasteners can lead to the
failure of the joint.
SAFETY ADVICE FOR CHARGER
Important! Danger! There are 4 pcs 1.2V Ni-cd battery
in screwdriver,Never short-circuit the battery or expose it
to moisture.Do not store it together with any metal parts
which could short-circuit the contacts.the machine could
overheat,start burning or explode.
Warning!
f This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
f Do not recharge non-rechargeable batteries.
f Children should be supervised to ensure that they do
not play with the appliance.
f Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied.
Other batteries could burst, causing personal injury
and damage.
f Never attempt to charge non-rechargeable batteries.
f Have defective cords replaced immediately.
f Do not expose the charger to water.
f Do not open the charger.
f Do not probe the charger.
ADDITIONAL SAFETY INSTRUCTIONS
FOR BATTERIES
f Turning the LED light off when not in use as this will
drain the battery.
f Never attempt to open for any reason.
f Do not expose the battery to water.
f Do not store in locations where the temperature may
exceed 40 °C.
f Charge only at ambient temperatures between 10 °C
and 40 °C.
f Charge only using the charger provided with the tool.
f When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
f Do not attempt to charge damaged batteries.
FEATURES (FIG. A)
1. Keyless chuck
2. Gear box
3. LED
4. LED switch
5. Housing
6. Switch
7. Everse-Rotation lever
8. Handle
9. Pivot release button
10. Charging hole
CHARGING THE BATTERY
Charging as shown,Must turn off the screwdriver. Only
Red lights up on the power indicator when you charging.
Charging time: 3 - 5 Hours. The charger wire plug-in The
position of the machine round hole,The charger plug in the
socket. As shown in the Fig. B.
POWER INDICATOR LIGHT
Three different colors of light (From Left: Green. Yellow.
Red) Charging State:
Only Red lights up when charging.
Operation State:
Green. Yellow and red light will light up at the same time,
With continued working, the battery voltage drops, and
when the Red light turns off, this implies that the battery is
used up and needs charging.
LED LIGHT
Just press the LED switch button gently, and the LED light
will turn on. Pressing the button again will turn off the LED
lights.
INSERTING TOOL BITS
Important! Always Turn off the machine before you
change the screw bit to avoid unintentional starting of the
machine.On/Off Trigger. In the use of driver, After make
sure align Outside the six-party of bit and hexagon hole of
output shaft. Keep it not fall off. If need to change bit, Turn
off the screwdriver. Pull out bit from hexagon hole of output
shaft by hand and change another one.
On/Off Trigger
Use the On/Off trigger to start the machine and keep
holding it for continuous operation.
REVERSE-ROTATION LEVER
Important! This is a can foldable cordless screwdriver,
The machine has to come to a complete stop before the
reverse rotation lever can be used.otherwise the machine
may be damaged.
Use the reverse-rotation lever to switch between clockwise
(normal) and anticlockwise rotation or vice-versa. With
the reverse-rotation lever in the central position the
trigger switch is locked and cannot be depressed .Put
the reverse-rotation lever in the central position before
you put the machine down,to avoid unintentional starting.
Right handhold handle, Left hand hold front of screwdriver.
At the same time left thumb press the black button (with
printed "Press"). Handle part rotated forwards 90 degrees.
Then will become straighten. Same way,If you want
curved. Do it like this.