Battery Disposal; Technical Data - Clatronic HSM 3086 HE Instrucciones De Servicio

Note: The lamp (9) does not give any indication of the charge
level of the battery. The charging lamp on the drive unit lights up
when there is contact with the mains adapter.
Beard Shaving
• Remove the cutting length comb (4). Press the I switch (1)
to turn on the device. Run the shearing blade across the
surface to be cut with the blade lying fl at against it to remove
the remaining hair.
• Press the O switch (1) to turn the device off.
Beard trimming and cutting / Cutting Hair
• In order to cut hair or trim beards, attach the cutting length
comb (4) and select the cutting length.
• Lock the selected cutting length of the beard trimmer (2) in
place with the release button (3). Press the I switch (1) to
turn the device on. Begin with the longest cutting length and
shorten your beard or the hair on your head step-by-step to
the desired length.
• Press the O switch (1) to turn the device off.
Contour cutting and neck shaving
• Remove the cutting length comb (4) and press the I switch
(1).
• The long hair cutter (8) makes it possible to follow the beard
contours precisely even in places that are diffi cult to access
and to cleanly shave the hairline in the area of the neck.
• Press the O switch (1) to turn the device off.
Haring, e.g. on the legs, bikini zone, under the armpits
• With this device it is possible to remove unwanted hair, e.g.
on the legs or under the armpits.
• We recommend that you have a bath or shower (for
example) after removing the hair, as otherwise the hairs are
too soft to be removed. The corresponding parts of the body
should be deodorised after shaving, if necessary.
• With this device you can also remove hair from your back,
for example. If necessary, attach the extension handle
(12). In order to make handling easier, angle the handle by
pressing the PUSH buttons together and locking in place.
This will produce an angle of approximately 90°. Press the
PUSH buttons again to return the handle to the straight
position.
Note: Depending on the quantity of cut hair it is advisable to
thoroughly clean the device from time to time as described
below in „Cleaning"!
Important: Do not use the device for more than 25 minutes.
Allow the equipment to cool down for 10 minutes, before using
it again.
05-HSM 3086 25
Cleaning
The regular cleaning and maintenance of the machine will
guarantee optimal results and a long life.
• Switch the device off with the O/I on/off switch and pull out
the plug.
• Use only a slightly damp and soft cloth to clean the machi-
ne.
• After use remove each time all hair left on the machine with
the supplied brush.
• Remove the cutting length comb and the shaving head
to blow out the fi ne particles of hair or remove with the
cleaning brush. Pull the shaving head (5) off carefully.
• Caution, do not touch the shaving foil or the blades of the
shaving head with your fi ngers!
• After using the machine apply each time 1-2 drops of an
acid-free oil (special oil (17)) on the cutting head.
• Hang the device up by the suspension eye.

Battery Disposal

The device contains rechargeable nickel-cadmium batteries.
Used batteries and accumulators (rechargeable batteries)
should not be disposed of in domestic waste.
These can be returned to a collection point for old batteries
or special refuse. Contact your local authority for further
information.

Technical Data

Model: .................................................................... HSM 3086 HE
Battery charging time (Hair-clipper): .................... approx. 7 hours
Power supply (Mains adapter): .................................230 V, 50 Hz
Protection class (Mains adapter): ............................................... ΙΙ
Power consumption:.............................. 2,5 W, DC 5,3 V, 140 mA
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
NiCd:
25
28.08.2006, 14:30:29 Uhr