Final Installation; Final Checks - Panasonic CQ-DP133U Manual De Instrucciones

Installation Guide
E
N
G
L
I
S
Speakers
H
Connect the speaker wires. See the wiring diagram
15
( page 28) for the proper hookups. Follow the di-
agram carefully to avoid damaging the speakers
and the stereo unit.
The speakers used must be able to handle more
than 45 W of audio power. If using an optional
audio amplifier, the speakers should be able to han-
dle the maximum amplifier output power. Speakers
with low input ratings can be damaged. Speaker
impedance should measure 4–8 Ω, which is typi-
cally marked on most speakers. Lower or higher
impedance speakers will affect output and can
cause both speaker and stereo unit damage.
Motor Antenna
Connect the car motor antenna lead to the dark blue
motor antenna relay control lead.
(Do not confuse the antenna lead with blue/white
stripe lead for a power amplifier.)
Battery
Connect the yellow battery lead to the correct radio
wire or to the battery fuse port on the fuse block.
Antenna
Connect the antenna by plugging the antenna lead
into the antenna receptacle.
Equipment
Connect any optional equipment such as an amplifi-
er, according to the instructions furnished with the
equipment. Leave about 12" (30 cm) of distance be-
tween the speaker leads/amplifier unit and the an-
tenna/antenna extension cord. Read the operating
and installation instructions of any equipment you
will connect to this unit.
Power
Connect the red power lead to the correct car radio
wire or to the appropriate fuse port on the fuse
block.
If the stereo unit functions properly with all these
connections made, disconnect the wires and pro-
ceed to the final installation.

Final Installation

Lead Connections
Connect all wires, making sure that each connec-
tion is insulated and secure. Bundle all loose wires
and fasten them with tape so they will not fall down
later. Now insert the stereo unit into the mounting
collar.
Congratulations! After making a few final checks,
you're ready to enjoy your new auto stereo system.
24
CQ-DP133U/DP103U/DPX153U
(Continued)

Final Checks

1. Make sure that all wires are properly connected
and insulated.
2. Make sure that the stereo unit is securely held in
the mounting collar.
3. Turn on the ignition to check the unit for proper
operation.
If you have difficulties, consult your nearest author-
ized professional installer for assistance.
Preparation
• We strongly recommend that you wear gloves
for installation work to protect yourself from
injuries.
• When bending the mounting tabs of the
mounting collar with a screwdriver, be careful
not to injure your hands and fingers.
• Disconnect the cable from the negative
terminal (see cautions below).
• Unit should be installed in a horizontal position
with the front end up at a convenient angle, but
not more than 30 ° .
Less than 30
Caution: Do not disconnect the battery terminals
of a car with a trip or navigational computer
since all user settings stored in memory will be
lost. Instead take extra care with installing the
unit to prevent shorts.
Dashboard Installation
Installation Opening
2 3 /
32
(53 mm)
7 5 /
"
32
(182 mm)
This unit can be installed in any dashboard having
an opening as shown above. The dashboard should
be 3 ⁄ " (4.75 mm)– 7 ⁄ " (5.56 mm) thick in order to
16 32
be able to support the unit.
Cautions:
¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
hands and fingers.
First complete the electrical connections, and
then check them for correctness.(
The included Mounting Collar q is
designed specially for this unit. Do
not use it to attach any other model.
y Power Connector
battery
°
Engage the Mounting
C ) in the
Springs (
mounting holes of the
Mounting Collar q
firmly.
Mounting Spring
(a) Using the rear support strap e
r Tapping screw
(5 mmø×16 mm)
"
Insert Mounting Collar q into the dash-
1
board, and bend the mounting tabs out
a page 28)
with a screwdriver.
The tabs to be bent vary depending on
the car. To securely install the unit, fully
bend a number of the tabs so that there
is no rattling.
Example:
q Mounting
Collar
Mounting Holes
t Mounting Bolt
Establish the rear connection of the unit.
2
After fixing Mounting Bolt t and Power Connector
y, fix the rear of the unit to the car body by either
Mounting Springs ( C )
method (a) or (b) shown below.
3
Insert Trim Plate i.
4
After installation re-
Mounting
connect the negative
Hole
(–) battery terminal.
(b) Using the rubber cushion (option)
Fire wall of car
Rubber cushion (option)
3 mmø
w Hex. nut
(5 mmø)
e Rear support strap
t Mounting bolt (5 mmø)
q Mounting collar
CQ-DP133U/DP103U/DPX153U
E
N
G
L
I
S
H
16
Tab
Rear support bracket
(provided on the car)
t Mounting bolt
(5 mmø)
q Mounting collar
25