General Operation - Stanley SDR1400 Manual De Instrucciones

20 • ENGLISH
USE
Variable speed switch (Fig. J)
Operate the product either in instant or continuous mode.
Instant Mode
f Switch the product On by pressing the variable speed
switch (7) (Fig. J).
f Switch the product Off by releasing the variable speed
switch (7).
Continuous mode (Fig. K)
f Switch the product On by pressing the variable speed
switch (7) and hold it in position (Fig. K, step 1).
f Press the lock-on button (6) and hold it in position
to lock the variable speed switch (7) (Fig. J, step 2).
f Release the lock-on button (6) and variable speed
switch (8). The variable speed switch is now locked on
for continuous use.
f Depress and release the variable speed switch (7)
to switch the product off.

General operation

f Check the product, its power cord and plug as well as
accessories for damage before each use. Do not use
the product if it is damaged or shows wear.
f Double check that the accessories and attachments
are properly fixed.
f Always hold the product on its handles. Keep the handles
dry to ensure safe support.
f Ensure that the air vents are always unobstructed
and clear. Clean them if necessary with a soft brush.
Blocked air vents may lead to overheating
and damage the product.
f Switch the product off immediately if you are disturbed
while working by other people entering the working
area. Always let the product come to complete stop
before putting it down.
f Do not overwork yourself. Take regular breaks to ensure
you can concentrate on the work and have full control
over the product.
Mixing (Fig. L)
Warning! During operation fine dust will be generated!
Some dusts are highly inflammable and explosive! Do not
smoke during operation, keep heat sources and open
flames out of the working area! Always wear a dust mask
to protect yourself against hazards resulting from fine dust!
The stirrer will come to a stop during operation if the
material is too firm! Switch the product off, lift the stirrer
out of the material and inspect the material before using
the product again! A blocked stirrer may cause overheating
the of motor. Hold the product firmly during operation. Do
not let the stirrer touch the bucket! This can cause damage
to the stirrer and bucket!
f Hold the product with 2 hands on both handles (2)
and insert the stirrer (5) into the material (Fig. L).
f Gently press variable speed trigger switch to start
operation at a low speed.
f Move the stirrer through the material until it is evenly
and completely mixed.
f Switch the product off. Let the stirrer come to a complete
stop before lifting it out of the mixing material.
Warning! Switch the product off, let it come to a
complete stop and disconnect it from the power supply if
the stirrer gets stuck in the mixing material. Only then free
the jammed attachment.
After use
Warning! Always switch the product off, disconnect the
product from the power supply and let the product cool
down before performing inspection, maintenance and
cleaning work!
CLEANING
f Keep the product clean. Remove debris from it after
each use and before storage.
f Regular and proper cleaning will help ensure safe use
and prolong the life of the product.
f Inspect the product before each use for worn and
damaged parts. Do not operate it if you find broken
and worn parts.
Warning! Only perform repairs and maintenance work
according to these instructions! All further works must be
performed by a qualified specialist!
f Clean the product with a dry cloth. Use a brush
for areas that are hard to reach.
f In particular clean the air vents (1) after every use with
a cloth and brush.
f Remove stubborn dirt with high pressure air
(max. 3 bar).
Note: Do not use chemical, alkaline, abrasive or other
aggressive detergents or disinfectants to clean this
product as they might be harmful to its surfaces.
f Check for worn or damaged parts. Replace worn parts
as necessary or contact an authorized service centre
for repair before using the product again.
MAINTENANCE
Your tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Warning! Before performing any maintenance, switch
off and unplug the tool.
f Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
f Regularly clean motor housing using a damp
cloth. Do not use any abrasive or solvent-based cleaner.