Operating Instructions; Safety Instructions - xtegra STICKFAST GX80 Instrucciones De Uso

GB
EDITION FEB 2017
STICKF ST
Warning
When using this hot melt glue gun always follow basic safety
precautions. Wear protective gloves, long sleeved clothing and
safety glasses, to reduce the possibility of accidental injury.
Read all the safety instructions.
Read all the safety instructions

Safety instructions

Xtegra ® Stickfast™ 240v model glue guns are recommended for
indoor use only and should not be used in wet or damp conditions.
Your work area should be well lit. The operating temperature of
the guns is between 120˚C- 230˚C. Do not touch the heated nozzle
or molten adhesive with bare skin. Protective gloves should al-
ways be worn. Careless handling can cause skin burns.
If molten adhesive comes into contact with the skin, immerse the
affected area immediately in cold water. Seek medical advice if
necessary, do not remove the adhesive from the skin.
Disconnect the electrical power supply to the glue gun after use,
before servicing and when changing accessories.
Allow time for the gun nozzle to cool down sufficiently before
handling. Never immerse the gun or its nozzle in water or other
liquids to accelerate the cooling process. Do not leave the gun
unattended while plugged in or still hot. If it is not to be reused
within one hour, disconnect the electrical power supply.
It is normal for this device to become warm during use and does
not indicate a problem.
Operation (All glue guns except SL150B)
> Use only recommended Stickfast™ adhesives in this glue
gun. The use of other manufacturers' products will
invalidate the warranty.
> Before using the gun for the first time check carefully for
signs of external damage. If any damage has occurred in
transit do not use it; return it to your supplier immediately.
> Attach the enclosed metal glue gun stand, locating the
hooks on its legs in the holes on either side of the gun
casing.
> Insert a Stickfast™ glue stick into the rear of the tool and
push the stick forward until slight resistance is felt.
> Plug the gun into a 240V AC outlet and allow the tool to
heat up for approximately 3-5 minutes. When the gun is
fully heated squeeze the trigger until the molten adhesive
begins to flow from the nozzle.
> Release the trigger to stop the flow. Do not apply
excessive pressure to the trigger as this can cause
blockages. If a blockage occurs, leave the gun to stand for
a minute, then gently try again.
> The first time a glue gun is used it may smoke from the
nozzle. This is normal and will stop as soon as glue has
filled the melt chamber.
> Apply the adhesive wherever it is required. When adhesive
can no longer be extruded from the tool, insert a new glue
stick into the rear of the tool to resume operation.
4

Operating Instructions

Operation (SL150B cordless model)
> Use only recommended Stickfast™ adhesives in this glue
gun. The use of other manufacturers' products will
invalidate the warranty.
> Before using the gun for the first time check carefully for
signs of external damage. If any damage has occurred in
transit do not use it; return it to your supplier immediately.
> Turn on to heat the gun; a red light is illuminated to
indicate power supply.
> Insert a Stickfast™ glue stick into the rear of the tool and
push the stick forward until slight resistance is felt.
> Pre-heat time is about 5-8 minutes before the gun is
ready to use. When the gun is fully heated squeeze the
trigger until the molten adhesive begins to flow from
the nozzle.
> Release the trigger to stop the flow. Do not apply
excessive pressure to the trigger as this can cause
blockages. If a blockage occurs, leave the gun to stand
for a minute, then gently try again.
> The first time a glue gun is used it may smoke from the
nozzle. This is normal and will stop as soon as glue has
filled the melt chamber.
> Apply the adhesive wherever it is required. When
adhesive can no longer be extruded from the tool, insert
a new glue stick into the rear of the tool to resume
operation.
> The indicator light flashes for two minutes before the
battery is exhausted and the heater turns off
automatically. Replace with a fully charged battery to
resume operation.
> Operating time is about 60 minutes (based on our
suggested battery capacity, 1.3Ah 36V)
> To release the battery, press the battery lock button. To
replace the battery, push battery in to the base of the gun
until the battery locks in place.
> Warning: Please take extra care with the heated nozzle;
the SL150B is a cordless model and it is easy to forget
that the gun may still be hot.