6- How To Use The Keyfob; Panic Alarm; 7- How To Control Your System Over The Phone - Honeywell Domonial Manual De Uso

6- How to use the keyfob*

E
N ARMING
G
• Press the total or part set** arming key:
The indicator light on the keyfob comes on briefly when you re l e a s e
L
the button.
The arming tone is emitted by the panel siren followed by the exit
I
delay beeps. If the system diagnoses a fault on arming, the arm i n g
tone is followed by a tone indicating a fault.
S
H
Always make sure that your arming request is followed by the arming tone.
If a perimeter fault is signalled on arming, please disarm the system before
verifying doors and windows equipped with contacts.
DISARMING
• Press the disarming key:
The indicator light on the keyfob comes on briefly when you release the
button.
The disarming tone is emitted by the panel siren.
Disarming will also stop the siren but it does not interrupt the transmission to the
ARC station.

PANIC ALARM

You can send an instant panic alarm whenever you feel threatened whilst at home,
even when your system is not armed :
• Press the "SOS" keys simultaneously
The siren is triggered (depending on configuration).
The Alarm Receiving Centre is alerted.
SPECIFIC KEY
The action of the lighting key depends on your configuration.
As an assistance key, it will enable you to call for assistance. In this case, press
the key, pause to see the indicator light come on, then press again.
As a remote control for electrical equipment***, pressing the key will turn the
equipment on and off successively.
* The system may include 0 to 10 keyfobs of this type.
** Provided that this function has been programmed by the installer, you can choose to protect only a part of
your premises whilst you are in the other part
*** This function requires an optional X10 extension with X10 modules
Total set arming
Part set arming
+
- 12 -

7- How to control your system over the phone

Control of your system over the phone is only possible from a multi-frequency
phone (tone dialling) or from your cellular phone. This function must be configure d
by the installer.
The Domonial control panel picks up your call after the number of rings configure d
by the installer or after it has been called twice successively.
• To access your system :
- Dial the phone number of your security system .
A 2-second beep sounds followed by the "Arpeggio" invitation tune.
- Enter a valid code within 30 seconds.
A high-pitch beep confirms that the code is valid.
• To arm your system :
- Dial * 21 to arm the total set, *22 to arm the part set, * 23 to arm the annex set.
Arming is confirmed as soon as you can hear a melody.
• To disarm your system* :
- Dial * 31 to disarm the total set, *32 to disarm the part set, *33 to disarm the annex set.
• To control an electrical device**:
- Dial *101 to *112 based on the number of the equipment programmed in your alarm system.
One short beep informs you that your equipment is active .
Two beeps inform you that your equipment is not active.
- Dial 1 to turn on the device, 0 to turn it off.
• To listen to the site and talk through the microphone of the control panel (if configured) :
- Dial *6.
- Dial 1 to talk, 0 to listen.
• To terminate the call :
- Dial * then #.
You security system ends the call.
Access your system Call system + Enter CODE
Total set arming *21
Part set arming *22
Annex set arming *23
Control equipment *101 - *112
Audio verification *6
Terminate the call *#
* This function is not available on all product versions and depends on country regulations.
** This function requires an optional X10 extension with X10 modules.
1: ON 0: OFF
1: TALK 0: LISTEN
- 13 -
E
N
G
L
I
S
H