S&P TH MIXVENT Serie Manual De Instrucciones página 6

ENGLISH
Thank you for placing your confi dence in S&P by buying this
product. It has been manufactured following current tech-
nical safety regulations and in compliance with EC stan-
dard.Please read this instructions booklet carefully before
installing or starting up the product. It contains important
information on personal and user safety measures to be
followed while installing, using and carrying out mainte-
nance work on the equipment. Once the product has been
installed, please hand in this booklet to the end user.Check
that the apparatus is in perfect condition while unpacking.
Any fault or damage caused in origin is covered by the S&P
guarantee. Please make sure that the apparatus coincides
with the product you have ordered and that the details on
the instructions plate fulfi l your necessities.
Transport and manipulation
- The packaging used for this apparatus has been de-
signed to support normal transporting conditions. The
apparatus must always be transported in its original
packaging as not doing so could deform or damage the
product.
- The product should be stored in a dry place in its orig-
inal packaging, protected from dust and dirt until it is
installed in its fi nal location. Do not accept delivery if the
apparatus is not in its original packaging or shows clear
signs of having been manipulated in any way.
- Do not place heavy weights on the packed product and
avoid knocking or dropping it.
Important information for the safety
of installers and users
- Installation must only be carried out by
qualifi ed persons.
- Make sure that the installation complies
with each country's current mechanical
and electrical norms.
- Once ready to use, the apparatus must ful-
fi l the following standards:
• Standard for Low Pressure Instalments
2006/95/CE
• Standard for Electromagnetic Compati-
bility 2004/108/CE.
- Ventilators, or apparatus that include
them, have been designed to move the air
in the area stipulated on their characteris-
tics plate.
- This apparatus must not be used in explo-
sive or corrosive atmospheres.
- If a ventilator is going to be installed to ex-
tract air from premises where a boiler or
other combustion apparatus are installed,
make sure that the building has suffi cient
air intakes to assure adequate combustion.
6
- The extractor outlet must not be connected
to a duct used to exhaust smoke or fumes
from any appliance that uses gas or any
other type of fuel.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental ca-
pabilities or lack of experience and knowl-
edge if they have been given supervision or
instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by children without su-
pervision.
Safety during installation
- Make sure there are no loose elements near the venti-
lator, as they could run the risk of being sucked up by
it. If it is going to be installed in a duct, check that it is
clean of any element that could be sucked up by theven-
tilator.
- When installing an apparatus, make sure that all the fi t-
tings are in place and that the structure which supports
it is resistant enough to bear its weight at full functioning
power.
- Before manipulating the apparatus, make sure the mains
supply is disconnected, even if the machine is switched
off.
- Check that the mains supply voltage and frequency val-
ues coincide with the stipulations on the characteristics
plate.
- The electrical installation must include a double pole
switch with a contact clearance of at least 3 mm, cor-
rectly sized and in accordance with the electrical stan-
dards of the country of installation
- Please follow the connections diagram for the electrical
connections.
- If an earth connection is necessary, check that it correct-
ly connected and that adequate thermal and overloading
protection has been connected and adjusted to the cor-
responding limits.
- If a ventilator is installed in a duct, the duct must be ex-
clusively for the ventilation system.
Starting up
Before starting up the machine, make sure that:
- The apparatus is well secured and the electrical connec-
tions have been carried out correctly.
- The safety devices have been adequately connected.
- No loose material or fi tting remains can be sucked up
by the ventilator. If the ventilator has been mounted in a
duct, make sure it is clear of loose material.
- The earth fi ttings are adequately connected.
- The electrical safety devices are correctly connected, ad-
equately adjusted and ready for use.
- The wire and electrical connections inputs are correctly
sealed and water-tight.