Specific Safety Instructions - Virax VISIOVAL 294020 Manual De Instrucciones

3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment (dust mask, non-
skid safety shoes, hard hat, hearing protection) used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making
any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.

Specific safety instructions

-
a) There is a danger of injury if the batteries are used or handled incorrectly. Do not throw the batteries onto
a fire or expose them to high temperatures: there is a danger of explosion.
b) If the batteries are used incorrectly, a liquid may leak out and irritate the skin; avoid all contact with this
liquid. If the skin does come into contact with this liquid, rinse with a large quantity of water. If the liquid
enters the eyes, rinse the eyes with water for 10 minutes and consult a doctor immediately.
c) Do not use the camera around television towers and other sources of magnetic and electrical fields: they
may cause interference.
d) External influences, such as static discharges, may cause faults. In this case, switch the camera off and
switch it back on again.
e) To avoid any damage during transport, the camera must always be transported in the case provided for
the purpose.
f) Protect the content of the case from water. Do not throw the case.
g) Pull and push the cable in a regular and even manner; do not force the cable if it becomes jammed.
Avoid rubbing the cable on sharp edges. Do not fold or twist the cable.
h) Wipe the cable with a dry cloth before putting it in the case to avoid the internal roller becoming dirty.
i) Ref. 294040: Change of plastic dome: do not wet nor touch the camera head; Before screwing back on,
slightly grease to maintain sealing (silicon grease)
The video inspection camera may only be used for optical inspection and to carry out recordings in tubes
and wells, gas evacuation installations, air vents, waste water pipes, sewers and so on.
The camera may only be used by personnel with the required level of skill. Any other used must be
considered as non compliant with the planned use and is not authorised.
Page
12
-EN-