Electrical Installation - Oase Water Jet Lightning Instrucciones De Uso

− Never run the pump without water! Otherwise the pump will be destroyed.
− Never use the pump for fluids other than water. Other fluids could destroy the unit.
− Never open the unit or its attendant components, unless this is explicitly mentioned in the operating instructions.
− Never carry out technical modifications to the unit.
− Only use original spare parts and original accessories for the unit. Only have repairs carried out by authorised
customer service points.
− Never look directly into the light source of the unit. The light beam's intensity could irreversibly damage the retina.
Pos: 86 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651
Pos: 87 /Alle Produkte/Überschriften/H1 Aufstellen @ 7\mod_1202907856718_121.doc @ 43934
Installation
Pos: 88 /Lampen/Wasserspieltechnik/Water Jet Lightning/Aufstellen Water-Jet-Lightning @ 8\mod_1220883652953_121.doc @ 52041
Attention! Dangerous electrical voltage!
Possible consequences: Death or severe injury.
− Install transformer and 12 V control box at a minimum safety distance of 2 m from the bank (E).
− Choose an installation place for the transformer and the 12 V control box that is splash-water protected.
Also protect the transformer and the 12 V control box against sun radiation (max. 40 °C).
Installation of the Water Jet Lightning (B, C, D)
Plan the installation of the Water Jet Lightning. When planning, take the cable and hose lengths into account!
Install the Water Jet Lightning horizontally on a firm base. The unit can be installed dry and in the water. When in-
stalled in the water, the upper section of the Water Jet Lightning must protrude out of the water by approx. 8 cm.
− Fasten the unit foot (12) on the base using 2 screws (13) (not included in our scope of delivery).
Pump installation and connection of the hoses (B, D)
Install the pump (4) as horizontally as possible. Raised installation can prevent the intake of dirt particles from the
bottom of the basin.
− Slightly loosen the union nut (14) at the Y distributor (15).
− Screw the reduction piece (16) on the pump (4) and insert the O-ring (17).
− Tighten the union nut (14) at the Y distributor (15).
− Screw the hose connection (19) on the Water Jet Lightning (1).
− Slide a hose clip (10) over the hose (6).
− Slide the hose (6) on the hose adapter (19) and secure with a hose clip (10).
− Connect the other end of the hose to the Y distributor (15) and secure with a hose clip (10).
Pos: 89 /Lampen/Wasserspieltechnik/Water Jet Lightning/Aufstellen Trafo und Steuerungsbox Water-Jet-Lightning @ 8\mod_1220884513083_121.doc @ 52067
Installing the 12 V control box
Variant 1 (F)
− Push the full length of the ground stake (8) into the ground at the desired position.
− Slide the 12 V control box (2) on the ground stake (8).
Variant 2 (G)
− Screw the 12 V control box (2) to the housing of the 12 V control box (2) on the base using 4 screws (21) (not
contained in the scope of delivery) through the screw gaps (22).
Setting up the transformer (H):
Place the transformer (5) close to the 12 V control box (2).
Note: Ensure that the cables are routed pull-relieved!
Pos: 90 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651
Pos: 91 /Alle Produkte/Überschriften/H1 Elektrische Installation @ 8\mod_1219935543509_121.doc @ 51295

Electrical installation

Pos: 92 /Lampen/Wasserspieltechnik/Water Jet Lightning/INS_Water-Jet-Lightning @ 8\mod_1221039895037_121.doc @ 52213
Connect the Water Jet Lightning with the 12 V control box and the transformer (H, I)
− Insert the pump plug (23) from the plug and the plugs (24) of the two Water Jet Lightning units into the respective
sockets for the pump (25) and the Water Jet Lightning (26) at the 12 V control box (2).
− Screw-connect the plug (27) of the transformer connection cable on the secondary side to the socket (28) at the rear
of the 12 V control box (2) and screw tighten with the union nut (29).
− Place the protection hood (3) over the 12 V control box (2).
Note: If you only want to operate one of the two Water Jet Lightning systems, plug the jumper plug (49) into the second
free socket (26).
n
Pos: 93 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651
Pos: 94 /Alle Produkte/Überschriften/H1 Inbetriebnahme @ 7\mod_1196625111244_121.doc @ 41417
Start-up
Pos: 95 /Lampen/Wasserspieltechnik/Water Jet Lightning/INB_Water-Jet-Lightning @ 8\mod_1221039989365_121.doc @ 52239
Caution! Do not damage the unit.
Protective measures: Never run the pump without water. Otherwise the pump will be destroyed.
Switching on the unit (J): Plug the power plug (30) of the transformer into the socket.
− The unit will start with program 1 (see chapter 'Control/Operation').
Switching off the unit (J): Pull the power plug (30) of the transformer.
Pos: 96 /Lampen/Wasserspieltechnik/Water Jet Lightning/Ausrichten Water-Jet-Lightning @ 8\mod_1221040206242_121.doc @ 52317
- GB -
13