RCM BYTE Serie Manual De Uso página 33

!
A !
TTENTION
E -
NSURE THAT THE WASHER DRIER IS CUT OFF FROM ANY VOLTAGE BEFORE PERFORMING ANY MAINTENANCE OPERATIONS
- Stop brush and suction rotation by pressing the relative symbols located on the start-up panel. sui
- for battery-operated machines with the "auto-stop" system, wait a few seconds before working on the washer-drier
- for battery-operated machines with "start-up keys", turn the key to the "0" position and then remove it.
- for "230V.AC cable-operated" machines, disconnect the cable from the power outlet.
Brush replacement
- Tilt the washer-drier to lift the front part (brush base) and keep it tilted by lifting wheel 1.
- Turn the brush 2 counter-clockwise A completely to unlock and remove it.
- Insert the new brush on the base and turn it clockwise B to lock it.
Replacing the drying edge or substituting the squeegee blade
If the front 3 and back 4 squeegee blades are no longer drying entirely, replace the drying edge. Substitute the blade if the edge is
completely worn.
Front blade
- lift the squeegee via lever 5
- dismantle the squeegee.
- remove the six knobs 6 holding down the cross piece 7 on the blade
- remove the blade, turn it and utilise new edge. Replace it if all 4 edges are completely worn.
- Reassemble
Back blade
If the back blade 4 of the squeegee is no longer drying entirely, replace the drying edge. Substitute the blade if the edging is completely worn.
- lift the squeegee via lever 5
- dismantle the squeegee.
- remove the six knobs 6 holding down the cross piece 7 on the blade
- remove the six screws 8
- remove the cross-piece 9
- remove the blade, turn it and utilise new edging. Replace it if all 4 edges are completely worn.
- Reassemble.
BATTERY CHARGING (WITH SUPPLIED BUILT-IN BATTERY CHARGER)
!
A !
TTENTION
CAREFULLY READ THE BATTERY CHARGER USER AND MAINTENANCE MANUAL
T
HE ELECTRICAL SYSTEM FOR BATTERY
- Stop brush rotation and suction by pressing the relative symbols located on the start-up panel.
- for battery-operated machines with "auto-stop systems" do not utilise the machine for a few seconds
- for battery-operated machines with "start-up keys", turn the key to the "0" position and then remove it.
!
A !
TTENTION
N
EVER ALLOW BATTERIES TO RUN DOWN COMPLETELY EVEN IF THE MACHINE IS NOT BEING UTILISED
AND PERFORM CHARGING IN A COVERED AND WELL
D
O NOT USE OPEN FLAMES OR SMOKE NEAR BATTERIES
T
AKE CARE WITH LIQUID AS IT IS CORROSIVE
D
O NOT PRODUCE ANY SPARKS NEAR BATTERIES
B
ATTERY GASES ARE EXPLOSIVE
Battery charging status is signalled by LEDs 1 located on the control panel. When the batteries begin to lose power, the LEDs pass to:
Green= batteries charged, controls are active > Yellow= batteries semi-charged, controls are active > Red (fi xed)= Batteries run down, brush output and
electrovalve disabled. > Red (fl ashing)= Batteries run down, all controls disabled.
Utilise the battery charger 2 to re-charge batteries.
Connect the plug 3 of the battery charger to the power outlet. The battery charger will fi rst perform a battery voltage test; if the test is positive, after a second
battery charging will begin signalled by a red LED 4 located on the battery charger.
The LEDs 5 indicate the re-charging phases:
R =
ED INITIAL CHARGING PHASE
!
A !
TTENTION
W -
ASHER DRIER ELECTRICAL CONTROLS AND SYSTEM SHALL BE EXCLUDED DURING BATTERY CHARGING PHASES FOR SAFETY PURPOSES
!
A !
TTENTION
I GEL LEAD
F OR OR OTHERS BATTERIES HAVE BEEN INSERTED IN THE WASHER
. "S FIG. 5
BATTERY CHARGER EE
WASHER-DRIER MAINTENANCE
-
OPERATED MACHINES MUST NOT BE POWERED
-
VENTILATED AREA
.
.
;
DO NOT PROVOKE SHORT
, Y =
ELLOW INTERMEDIATE PHASE
S . THE SETTINGS MUST BE DONE WHEN THE BATTERY CHARGER IS SWITCHED OFF.
FOR ETTINGS
(FIG.4)
(FIG.5)
. P
ROCEED AS FOLLOWS
.
.
-
CIRCUITS OR INVERT THEIR POLARITY
, G = F
REEN INAL PHASE AND CHARGING STOP
- ,
DRIER PERFORM THE SPECIFIC SETTINGS ON THE TWO
ITALIANO ENGLISH
. P
ROCEED AS FOLLOWS
BEFORE CHARGING BATTERIES
:
. R
EMOVE THE RECOVERY TANK
.
, .
THE BATTERY IS READY
.
"
DIP SWITCHES
:
" 6
OF THE
33 33