Technical Data; Proper Use; Cutting Grass - Einhell Royal AGS 7,2 Manual De Instrucciones

Anleitung AGS 7,2 11.02.2005
GB
When the tool is not being used, store it so that
the blades cannot be touched accidentally.
Take care not to overload the tool and do not use
it on jobs for which it is not intended.
The tool requires regular inspection and
maintenance. Always replace damaged blades in
pairs. If the tool suffers any damage from impact
(falling on hard ground etc.), have it checked
immediately by a specialist.
Look after your tool carefully. Keep it clean and
sharp to ensure efficient and safe cutting. Follow
the maintenance and cleaning instructions.
4. Important information
The battery pack supplied with the tool is not
charged. The battery pack has to be charged
before you use the tool for the first time.
Charge the battery pack with the charger
supplied. Do not use the supplied charger to
charge other items of equipment.
The battery pack does not reach its maximum
capacity until it has been charged and
discharged approximately five times.
NC battery packs lose their charge even when
they are not being used. Regular charging is
therefore recommended.
Please check the data marked on the rating plate
of the battery charger. Connect the battery
charger only to an identical mains supply to that
on the rating plate.
In heavy use the battery pack will become warm.
Allow it to cool to room temperature before
commencing with the charging.
Never throw old batteries in the fire. Risk of
explosion!
Used and defective batteries do not belong in the
refuse bin. Think of the environment - cadmium
is toxic. For proper disposal of used and
defective batteries, send them postage-paid to
the ISC company or take them to a special
collecting station in your area. Ask at your local
council offices for the nearest used battery
collecting station.
Protect the battery charger and cable from
damage and sharp edges. Damaged cables are
to be replaced without delay by an electrician.

5. Proper use

The AGD 7.2 is designed for cutting the edges of
lawns and small areas of grass in private and hobby
gardens.
8
6:57 Uhr Seite 8
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
For the tool to be used properly it is imperative to
follow the instructions set out in the manufacturer's
directions for use.
Important! It is prohibited to use the tool to chop
material for composting because of the potential
danger to persons and property.

6. Technical data

Cutting width of the grass cutter:
Running time max.: approx. 60 min.
Battery pack: 7,2 V / 1500 mAh
Charging time:
Sound power level:
Vibration a w :
Battery charger:
Voltage: 230 V ~ 50 Hz
Rated voltage output:
Rated current:
The machine may exceed 85 dB (A). The operator
will require noise protection measures if this is the
case. The noise is measured in accordance with IEC
59 CO 11, IEC 704, DIN 45635 part 21, NFS 31-031
(84/538/EWG).
The value of the vibrations emitted by the handle
was determined in compliance with ISO 5349.
7. Starting up
7.1 Operation
The area to be cut must first be cleared of stones
and other solid objects. The safety lock-off (Fig.
1/Pos. 3) prevents the tool being started
unintentionally. The safety lock-off must be unlocked
before the grass cutter is put into operation. To do
so, push the safety lock-off from the right or left and
keep it pressed. If you now actuate the ON/OFF
switch (Figure 1 / Item 4) at the same time, the tool
will be started.
To switch off the tool, let go of the ON/OFF switch
(Figure 1 / Item 4).

7.2 Cutting grass

Allow the grass cutter to glide over the ground. The
best cutting performance is achieved on dry lawns.
When you notice a drop in cutting performance,
recharge at once so that the batteries do not become
90 mm
4-6 h
89 dB(A)
≤ 2.5 m/s
2
12 V DC
300 mA