Assembly; Use Of Brushcutter; Preparing For Use; Stopping Engine - IBEA 45-Z Manual De Instrucciones

GB
ENGLISH
WARNING : The weight of the machine must be supported
by the waist-band (A).
Fig.12/1 - To loosen the straps, pull the the handle of the
buckle upwards.
WARNING Carefully read the safety precautions before
using the brushcutter.
Put on the harness. For balancing and adjustment see

ASSEMBLY

Always keep both hands on the handles operating the
brushcutter.
Use the bushcutter on the right side of the operator as
illustrated Fig. 13.
Always check the cutting tool for cracks after hitting foreign
objects.
ACTIVE NYLON HEAD SYSTEM "ACTIVE patent" Fig. 14
- Only use line of the same diameter as the original to avoid
overloading the engine.
- Stop the engine and put on the safety gloves.
Turn the knob (C), clockwise, until the arrow (E) is in line
with one of the eyelets (D). Insert the pipe (A) Through both
eyelets fit the line through the pipe.
- Remove the pipe on either side of the nylon head.
FUEL
2 STROKE - WARNING. The machine is equipped with a
two stroke engine. Always run the machine with fuel, which
is mixed with oil. Only prepare the quantity of fuel for each
job. Do not smoke. Refill when the engine is switched off and
away from naked flame. AIways use a minimum octane
number of 90. Mix fresh gasoline and ACTIVE oil in the ratio
of 50:1 (2%). If the ACTIVE oil is not available use a good 2
stroke oil quality in the ratio of 25:1 (4%) see fig.15
Important Always shake this fuel mix vigorously each time
you use it. Fuel mix properties deteriorate with time we
therefore recommend that you only make the quantity of fuel
mix you will need for each usage. Do not use fuel mix more
than a week old as this could damage the engine. Fill the
brushcutter fuel tank only to 3/4 capacity to allow for fuel
expansion.
FUELING
WARNING Always shut off the engine before refueling. Slowly
open the cap of the fuel tank, when filling up with fuel, so that
possible over pressure disappears. Tighten the fuel cap
carefully after fuelling. Always move the machine at least 3
m (10Ft) from the fueling area before starting. Before fueling
clean the tank cap area carefully, to ensure that no dirt falls
into the tank make sure that the fuel is well mixed by shaking
the container before fueling.
Fig. 12/2 - To unfasten the hook push at the same time the
two levers (A) as show in the picture.

6. USE OF BRUSHCUTTER

- Pull the line till the ends of the line are at the same length.
- turn the knob clockwise (every 3 turns stretch the lines)
until the line is wound onto the spool.
TO USE LINE FEEDER
Keep the engine at high RPM and tap or knock the underside
of the nylon head knob against the ground. Each knock will
feed approximately 3cm. of line.
WARNING: Do not knock the nylon head against hard
surfaces.
WARNING: fig.20 - only in extreme cases where one
on the left hands side of your body it is imperative to fit an
elbow (1) to the muffler (3). Before securing the elbow (2) it
is necessary to position it in such a way as to deflect the hot
gases away from the harness and the back of the operator.

7. PREPARING FOR USE

STARTING
Fig.1 - Lay brushcutter on a flat bare surface and make
sure that the cutting tool is free to work .
Move ignition switch to (1). Fig.1
Press throttle trigger (A) and push down the botton (B) to
lock the trigger in half-throttle position, release the trigger
(A) Fig. 1/A
Push primmer bulb (A) repeatedly 5 to 6 times Fig.1/C
Move choke lever (A) to choke position (B) Fig.1/B
Holding the unit down pull the starting handle until engine
attempts to run then move the choke lever (A) to open position
(C) Fig. 1/B
Pull starter until engine runs.
Once the engine has started, press throttle trigger (A) to
release it from the half-throttle position and let the engine
idle.
Warning: fig.1B/1C - once the engine is warmed up do not
use the primmer bulb (C) and the choke (A) to start up again.
Do not release the starter handle in pulled out position, as
this may damage the starting ass'y.

STOPPING ENGINE

Set the throttle lever (A) Fig.1/A to idle position and wait a
few seconds to let the engine cool off. Move the ignition switch
to "stop" position (0). Fig.1
WARNING: with the engine idling (2600 - 3000 rpm)
the cutting tool should not rotate.
If the idle speed is too high turn counterclockwise the screw
(H) Fig. 3
24
has no alternative but to operate the brushcutter