Regular Maintenance; Maintenance Schedule; Storage - IBEA 45-Z Manual De Instrucciones

WARNING: From time to time make sure all brushcutter
screw are firmly secured.Replace damaged,worn,cracked or
wapped blades. Always make sure nylon string head or blade
have been assembled correctly and blade fastener is
tightened.
IN AIR FILTER SPONGE
Fig.16 (4.0/4.5/5.5/6.5- 2T)
- Check and clean regularly according to the working
conditions.
- Remove the cover (1)
- Take out the elements (2)
- Wash the elements (2) with mix gasoline / oil and wring
strongly.
- IMPERATIVE to oil the element (2)
- Check the parts and replace them if necessary. Reassemble
in the opposite sequence to that listed for disassembly.
WARNING:For best results and long engine life, use
ACTIVE air filter sponge oil Ref. 21010.
AIR FILTER PAPER IN (optional - for 4.5/5.5/6.5)
- Regularly check the air filter, based on working
conditions.
- remove cover (1)
- remove filters (2)
- use only compressed air
- to not damage the paper of filter
- to not wash with water, gasoline or liquids
- to not put oil on the paper
- to change the filter if it is damaged
FUEL FILTER fig.17
To clean and to replace fuel filter, remove the fuel tank cap
(3) and pull out the filter (2) with a hook wire (1) or long forleps.
Check fuel filter (2) periodically; replace it if too dirty.
ENGINE (IN ORDER TO AVOID TROUBLES)
Regularly: it is important,in order to avoid engine overheating,
to remove dust and dirt from slots,from cylinder, cover and
fins using a brush or compressed air.
MAINTENANCE AT 200 hours working
1) Clean the fuel tank and replace the fuel filter
2) Clean the engine.
3) Replace the spark plug.
Follow all the maintenance instructions previously described.
- Clean the brushcutter completely and lubrificate the metallic
parts.
- Empty fuel tank and run engine until dry.Store brushcutter
in a dry place.

8. REGULAR MAINTENANCE

ENGINE
Regularly: it is important,in order to avoid engine overheating,
to remove dust and dirt from slots,from cylinder, cap and fins
using a brush or compressed air.
SPARK PLUG fig.18 for 2T
From time to time(at least every 50 hours)remove and clean
the spark plug and check the electrode gap(0.5-0.6
mm.).Replace spark plug about every 100 working hours or
whenever it is extremely encrusted. Heavily encrusted
electrodes can result from an incorrect carburetor setting or
from wrong fuel mixture (too much oil in the fuel) or a poor
quality oil in the fuel mix.Check and correct.
FLEXIBLE TRANSMISSION fig.2
- Every 50 working hours remove the flexible shaft (A) from
the clutch housing (B).
- Remove the inner flexible shaft (G) from the sheath (A) and
put grease on it.
- Reassemble in the opposite sequence to that listed for
disassembly.
Recommended grease: Special ACTIVE "NO MELT" Ref.
21230.
BEVEL GEAR fig.19
Every 50 working hours inject the bevel gear with gear grease
trough the hole (A).
Recommended grease: Special ACTIVE "NO MELT" Ref.
21230.
BLADE
AIways check the general conditions of the blade.Replace
blade if craked,chipped or damaged in any way.

9. MAINTENANCE SCHEDULE

4)* Remove the cylinder and clean off carbon deposits on
piston, cylinder and exhaust system.
5)* Disassembly the carburettor and replace the diaphragms.
6)* Check and adjust engine valve clearance.
*) As to the procedures for these items, please refer to
your IBEA dealer.

10. STORAGE

- Remove the spark plug,put a small amount of oil into the
cylinder rotate the crankshaft several times using the starting
in order to distribute the oil,put the spark plug back in.
ATTENTION: all maintenance operations not reported in this
manual must be carried out by an authorized service center.
25
GB
ENGLISH