Lock-Release Time - Fermax CITYLINE VDS-BUS2 Manual De Instalador

VDS-BUS2 Programming
VDS-BUS2 Programming
To reset mapping:
- disconnect power supply.
- connect the power supply to the
amplifier by
programming button and holding it
until you hear the confirmation beep.
ADVANCED PROGRAMMING: Lock-Release Timing
There are two programmable lock-release activation times:
- Lock-release time set from the residence.
- Lock-release time set from the exit button (connected to the "BS" and "-"
terminals).
BUTTON Panel Programming
Carry out the following steps:
1.- With the power supply disconnected, short circuit the "Bs" and "-" (negative)
amplifier terminals (or press the exit button where one exists).
2.- Maintaining the short-circuit induced above connect the system's power supply
(at this point it will no longer be necessary to maintain the short circuit or hold
down the exit button).
A confirmation tone will sound once you enter programming mode.
3.- Following the confirmation tone, the lock-release time as currently
programmed from the residence will be indicated by way of a number of
beeps at 0.5 second intervals.
4.- Once these indicator tones have concluded, or before they conclude, press
any button on the panel, with one press for each second to be programmed
(from 1 to 99 seconds).from the residence or following the indicator tones),
wait 5 seconds before taking any other action.
VDS-BUS2 Programming
VDS-BUS2 Programming
To reset mapping:
- disconnect power supply.
- connect the power supply to the
amplifier by
programming button and holding it
until you hear the confirmation beep.
ADVANCED PROGRAMMING: Lock-Release Timing
There are two programmable lock-release activation times:
- Lock-release time set from the residence.
- Lock-release time set from the exit button (connected to the "BS" and "-"
terminals).
BUTTON Panel Programming
Carry out the following steps:
1.- With the power supply disconnected, short circuit the "Bs" and "-" (negative)
amplifier terminals (or press the exit button where one exists).
2.- Maintaining the short-circuit induced above connect the system's power supply
(at this point it will no longer be necessary to maintain the short circuit or hold
down the exit button).
A confirmation tone will sound once you enter programming mode.
3.- Following the confirmation tone, the lock-release time as currently
programmed from the residence will be indicated by way of a number of
beeps at 0.5 second intervals.
4.- Once these indicator tones have concluded, or before they conclude, press
any button on the panel, with one press for each second to be programmed
(from 1 to 99 seconds).from the residence or following the indicator tones),
wait 5 seconds before taking any other action.
Amplifier
pressing the
Amplifier
pressing the
CN1
AMPLIFICADOR BUS-2
A
BUS-2 AMPLIFIER
B
AMPLIFICATEUR BUS-2
C
BUS-2 VERSTÄRKER
D
CN2
PAN & TILT
10
JP2
MASTER SLAVE
JP3
LEDS ON
LEDS OFF
CN1
PACK EXTENSION
CN2 TARJETERO
CARD HOLDER
BUS-2
B B NC NO C
CN3
CN4
CN3 LEDS ESTADO
STATUS LEDS
CN4
TEST
CN1
AMPLIFICADOR BUS-2
A
BUS-2 AMPLIFIER
B
AMPLIFICATEUR BUS-2
C
BUS-2 VERSTÄRKER
D
CN2
PAN & TILT
10
JP2
MASTER SLAVE
JP3
LEDS ON
LEDS OFF
CN1
PACK EXTENSION
CN2 TARJETERO
CARD HOLDER
BUS-2
B B NC NO C
CN3
CN4
CN3 LEDS ESTADO
STATUS LEDS
CN4
TEST
AUDIO
IDIOMA
LANGUAGE
EXIT EXIT
MIC
- S
BS PROG
+12
SW1
SW1
Pag 13
AUDIO
IDIOMA
LANGUAGE
EXIT EXIT
MIC
S
BS - PROG
+12
SW1
SW1
Pag 13