Publicidad
Idiomas disponibles
Idiomas disponibles
(Pa)
80
70
60
M
50
L
LL
40
LLL
30
20
10
0
650
700
750
800
Model:71
(Pa)
120
100
80
M
L
60
LL
LLL
40
20
0
750
850
950
1050
Model:80
(Pa)
120
100
80
M
L
60
LL
LLL
40
20
0
750
850
950
1050
Model:90
(Pa)
120
100
M
80
L
LL
60
LLL
40
20
0
1050
1150
1250
Model:112
POWER
SH
H
850
900
950
1000
1050
Q(m
/h)
3
Fig.6-6
POWER
SH
H
1150
1250
1350
Q(m
Fig.6-7
POWER
SH
H
1150
1250
1350
Q(m
Fig.6-8
POWER
SH
H
1350
1450
1550
Q(m
Fig.6-9
(Pa)
160
140
(Pa)
120
0
100
10
LLL
20
80
30
60
40
50
40
60
70
20
0
1250
1350
Set proper external static pressure (ESP) according to the actual installation
conditions. Otherwise it may cause some problems.
If the connecting duct is long and the ESP setting is small, the airflow will
(Pa)
be very small, leading to poor performance.
10
If the connecting duct is short and the ESP setting is large, the airflow will
be very large, leading to higher operating noise and even water may be
20
blown out through the air outlet.
30
40
ESP can be set through the DIP switch SW2 on the main board or the new
50
wired controller. Please refer to Part "7.3 DIP switch settings on main board"
60
for SW2 setting or the wired controller manual for wired controller setting.
70
Four ESP can be set through DIP switch SW2.
80
90
Capacity
100
2.2-7.1kW
8-11.2kW
14kW
/h)
3
Ten ESP can be set through the new wired controller.
Capacity
00
2.2-7.1kW 0Pa
8-11.2kW 10Pa
14kW
30Pa
(Pa)
10
Selection instructions for static pressure set through the wired
20
controller
30
40
1) The IDU static pressure can be set using the wired controller
50
with the static pressure settings function
60
2) Hold the "Function" button + "Mode" button for 5s to enter the
70
parameter settings interface (the unit must be off);
80
3) After accessing the parameter settings interface, the tempera-
90
ture area displays "C0". Press the "▲" and "▼" buttons to
100
switch parameter code. After "C9" is selected, press the "OK"
button to access the parameter settings interface. Press the "▲"
and "▼" buttons to adjust the parameter value (the following
/h)
3
table provides the corresponding static pressures of the values).
Press "OK" to save the parameters and complete the parameter
settings.
4) Press "Cancel" to return to the previous layer until exiting the
parameter settings, or exit the parameter settings when there
(Pa)
are no operations after 60s.
10
5) On the parameter settings interface, the wired controller does
20
not respond to the remote control signal. The wired controller
30
does not respond to the APP remote control signal.
40
6)The "Mode", "Fan Speed", "Swing", "Function" and "On/Off"
50
buttons are invalid on the parameter settings interface.
60
70
80
90
100
/h)
3
31
SH
H
M
L
LL
1450
1550
1650
1750
1850
Model:140
ESP1
ESP2
ESP3
10Pa
30Pa
70Pa
20Pa
40Pa
70Pa
40Pa
70Pa
100Pa
01
02
03
04
05
06
10Pa 20Pa 30Pa 40Pa 50Pa 60Pa 70Pa 70Pa 70Pa
20Pa 30Pa 40Pa 50Pa 60Pa 70Pa 80Pa 90Pa 100Pa
40Pa 50Pa 60Pa 70Pa 80Pa 90Pa 100Pa 125Pa 150Pa
(ex. WDC-120GWK)
POWER
(Pa)
30
40
50
60
70
80
90
100
125
150
1950
2050
Q(m
/h)
3
Fig.6-10
ESP4
50Pa
100Pa
150Pa
07
08
09
Publicidad
