Functional Description - Berner BP 40-82 C Manual De Instrucciones

OBJ_BUCH-1135-001.book Page 14 Tuesday, January 12, 2010 1:32 PM
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Planer Safety Rules
¢ Wait for the cutter to stop before setting the
tool down. An exposed cutter may engage the
surface leading to possible loss of control and seri-
ous injury.
¢ Hold the power tool by insulated gripping
surfaces only, because the cutter may con-
tact its own cord. Cutting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
¢ Use clamps or another practical way to
secure and support the workpiece to a stable
platform. Holding the work by your hand or
against the body leaves it unstable and may lead to
loss of control.
¢ Use suitable detectors to determine if utility
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explosion.
Penetrating a water line causes property damage
or may cause an electric shock.
¢ Do not reach into the saw dust ejector with
your hands. They could be injured by rotating
parts.
14 | English
¢ Apply the machine to the workpiece only
when switched on. Otherwise there is danger of
kickback when the cutting tool jams in the work-
piece.
¢ When working, always hold the planer in
such a manner that the planer base plate
faces flat on the workpiece. Otherwise the
planer can become wedged and lead to injuries.
¢ Never plane over metal objects, nails or
screws. The planer blade and the blade shaft can
become damaged and lead to increased vibra-
tions.
¢ Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
¢ Never use the machine with a damaged
cable. Do not touch the damaged cable and
pull the mains plug when the cable is dam-
aged while working. Damaged cables increase
the risk of an electric shock.
Products sold in GB only: Your product is fitted
with an BS 1363/A approved electric plug with inter-
nal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its
place by an authorised customer service agent. The
replacement plug should have the same fuse rating as
the original plug.
The severed plug must be disposed of to avoid a pos-
sible shock hazard and should never be inserted into
a mains socket elsewhere.
Products sold in AUS and NZ only: Use a residual
current device (RCD) with a rated residual current of
30 mA or less.

Functional Description

Read all safety warnings and all
instructions. Failure to follow the warn-
ings and instructions may result in elec-
tric shock, fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
Intended Use
The machine is intended for planing of firmly sup-
ported wooden materials, such as beams and boards.
It is also suitable for beveling edges and rebating.
2 609 932 749 • 12.1.10