Français; Rabot À Chanfreiner Ce89E - Virutex CE89E Manual De Instrucciones

Unscrew screws H (Fig. 4) and remove protection G.
Replace the worn belt with a VIRUTEX original spare,
taking care to fit it correctly into the pulley cogs, never
forcing it.
8. MAINTENANCE OF THE
BRUSHES AND COLLECTOR
Disconnect from the mains before car-
rying out any maintenance operations.
The brushes must be replaced when they reach a minimum
length of 5 mm (Fig. 5)
Unscrew the black caps E (Fig. 2) on the housing and
remove the brushes from the guide. Replace them with
new Virutex original spares, ensuring that they move
smoothly inside the guides. Screw on the cap which
covers them and leave the machine running for 15
minutes. If the collector is burned or uneven it should
be repaired by a Virutex service agent.
Always keep the lead and plug in good working condition.
9. ACCESSORIES
3540118 - Set of reversible straight MD blades CE24E/
CE35E (Included with equipment)
3531019 - Set of reversible straight AR blades CE24E/
CE35E
3599101 - Set of standard blades
10. NOISE AND VIBRATION LEVEL
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-14 and EN 60745-1 and serve as a basis for
comparison with other machines with similar applications.
The indicated vibration level has been determined for the
device's main applications and may be used as an initial
value for evaluating the risk presented by exposure to
vibrations. However, vibrations may reach levels that are
quite different from the declared value under other ap-
plication conditions, with other tools or with insufficient
maintenance of the electrical device or its accessories,
reaching a much higher value as a result of the work
cycle or the manner in which the electrical device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).
11. WARRANTY
6
All VIRUTEX power tools are guaranteed for 12 months
from the date of purchase, excluding any damage which
is a result of incorrect use or of natural wear and tear
on the machine. All repairs should be carried out by the
official VIRUTEX technical assistance service.
VIRUTEX reserves the right to modify its products
without prior notice
F R A N Ç A I S
RABOT À CHANFREINER CE89E
Important
Avant d'utiliser la machine, lisez attenti-
vement ce MANUEL D'INSTRUCTIONS et la
BROCHURE D'INSTRUCTIONS GÉNÉRALES
DE SÉCURITÉ qui vous sont fournis avec
cette machine. Assurez-vous de bien
avoir tout compris avant de commencer
à travailler sur la machine.
Gardez toujours ces deux manuels
d'instructions à portée de la main pour
pouvoir les consulter, en cas de besoin.
1. INSTRUCTIONS DE SÉCURITÉ
POUR L'UTILISATION DU RABOT
Lire attentivement la BROCHURE D'INS-
TRUCTIONS GÉNÉRALES DE SÉCURITÉ
jointe à la documentation de la machine.
1. Avant de brancher la machine, vérifier si la tension
d'alimentation correspond à celle indiquée sur la plaque
des caractéristiques.
2. Prendre soin de ne pas mettre les mains sur la zone
de coupe, et de toujours prendre la machine par la
poignée.
3. Utiliser uniquement des couteaux d'origine VIRUTEX.
Ne jamais utiliser de couteaux qui ne seraient pas
aiguisés, ayant des mesures incorrectes, défectueux ou
en mauvais état.
Toujours utiliser le porte-lames et les supports de la-
mes d'origine VIRUTEX montés sur la machine. En cas
de besoin, les remplacer par des pièces de rechange
d'origine VIRUTEX.
4. Il faut travailler avec un aspirateur de copeaux pour
prolonger la durée de vie des couteaux et éviter des
cassures éventuelles.
5. Éviter de couper des clous. Vérifier la surface à travailler
avant de rabotter.