Descargar Imprimir esta página

Makita DSC102 Manual De Instrucciones página 12

Ocultar thumbs Ver también para DSC102:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 44
OPERATION
CAUTION:
Make sure that the correct size of
the cutting dice are installed to the tool. Check
the cutting capacity written on the the cutting dice
before cutting.
CAUTION:
Before pulling the switch trigger,
be sure to set the threaded rod so that its thread
fits with those of cutting dice. Incorrect alignment
of the threads may break the cutting dice and cause
personal injury by flown off fractions.
CAUTION:
Replace the cutting dice if the
cutting edge is chipped or deformed.
When cutting, place the threaded rod perpendicular to
the cutting line as shown in the figure.
► Fig.18: 1. Cutting line
NOTE: When cutting a threaded rod made of ductile
metal such as stainless steel, burrs may be generated
on the cut end. Remove burrs with a file in this case.
► Fig.19: 1. Threaded rod 2. Burr
Cutting secured threaded rods
When cutting a threaded rod which is secured to the
building structure such as the ceiling, wall, floor, etc.,
follow the procedure below :
► Fig.20: 1. Threaded rod 2. Cutting die on the sta-
tionary mount
1.
Bring the tool so that the threaded rod is posi-
tioned between the cutting dice.
2.
While the threaded rod contacting with the rod
guide, fit the thread of the rod with that of the cutting die
on the stationary mount.
Pull and hold the switch trigger until the cutting is
3.
finished and the jaw of the cutting dice comes to fully
opened position.
NOTICE:
Clean the front face of the tool and the
tip of the guide scale before operation. They may
dirty the contacting surface.
Cutting loose threaded rods
When cutting a loose threaded rod on the floor or a
work table, follow the procedure below :
► Fig.21: 1. Threaded rod 2. Cutting die on the sta-
tionary mount
Position a threaded rod between the cutting dice.
1.
2.
While the threaded rod contacting with the rod
guide, fit the thread of the rod with that of the cutting die
on the stationary mount.
Pull and hold the switch trigger until the cutting is
3.
finished and the jaw of the cutting dice comes to fully
opened position.
When cutting a long threaded rod which is hard to hold
by hand, place the tool as illustrated. The tool can be
placed flat. The cover also can be used for supporting
the end of the threaded rod.
► Fig.22: 1. Cover (Position 1) 2. Rod guide (Position
1) 3. Cover (Position 2) 4. Rod guide
(Position 2)
The cover has markings to indicate its position.
Depending on the size of the threaded rod, put the
cover in the position as shown in the table as well as the
rod guide.
Position
1
2
Quitting the cutting in the middle
CAUTION:
Never try to pull out the tool forci-
bly from the threaded rod. It may cause unexpected
start up which cause personal injury or damage to the
cutting dice and tool.
When quitting the cutting in the middle, set the revers-
ing switch lever to the reversing position and pull the
switch trigger until the threaded rod is completely
released from the cutting dice.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Replacing the cutting dice
NOTICE:
Replace the both cutting dice at the
same time. Replacing the one side of the cutting die
may generate burr on the threaded rod.
Replace the cutting dice when it is chipped, deformed,
or the cutting gets dull. To replace, follow the instruc-
tions in "Installing the cutting dice".
► Fig.23: 1. Chipping 2. Deformation
One cutting die has two cutting edges and thick side
and thin side. Switch the installation positions of the
cutting dice if you have not used the other sides of the
cutting edges.
► Fig.24: 1. Cutting edge 2. Thin side 3. Thick side
12 ENGLISH
Size of threaded rod
W3/8, M10
M8, M6

Publicidad

loading