Hoover Steam capsule handy Manual De Instrucciones página 4

GETTING TO KNOW YOUR CLEANER
A. Power Light
B. Steam Outlet
C. Steam Release Trigger
D. Power Cord
E. Water Tank Cap
F. Clean Water Tank
G. Steam Regulator
H. Angled Nozzle
I. Small Round Brush
J. Accessories support
K. Window Squeegee
L. Steam Brush Nozzle
M. Small Cloth
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. You can choose from a variety of accessories depending on what tasks you are
using the product for. These can be seen on Images. [6,7,8]
USING YOUR CLEANER
BEFORE YOU BEGIN CLEANING
Twist the water tank cap [E] anticlockwise and remove. [1]
1.
Fill the clean water tank [F] with normal tap water or demineralized water [2]. Do not
2.
add any chemicals, detergents or perfumes to the clean water tank.
Re-fit the water tank cap [E] into the clean water tank [F] and turn it clockwise to
3.
lock it. [1]
Attach the accessory most suited for the kind of surface to be cleaned. [10]
4.
Plug The mains cable [D] into a suitable earthed mains power outlet [3]. The power
5.
light will illuminates and start flash [A],when the light stop flashing and remain
constant,the steam will be available.
To deliver steam, press the steam release trigger [C].
6.
NOTE: In order to significantly reduce mineral build-up and prolong the life of your steam
mop the use of distilled or de-mineralized water in the unit is highly recommended.
IMPORTANT: Always unplug the cleaner when adding water or changing a Textile Pad.
NOTE: Wash the Textile Pad prior to use to remove any lint.
ELECTRONIC STEAM REGULATION
The steam pressure can be adjusted by moving the steam regulator [G] from lower to
higher flow, depending on the cleaning application.
WARNING:
Before putting the product away, empty the water tank.
WARNING: Even when unplugged, the product may release steam.
Therefore handle it carefully, and store out of reach of anyone who does
not know how to use it.
PRECAUTIONS:
1. For cleaning leather, wood or delicate fabrics especially dralon, velvet and other pile
surfaces, consult the manufacturers instructions. Clean only by using the product at
a safe distance together with a soft cloth and always do a test on a non visiblepart of
the item first or on a sample. Allow the test area to dry completely before observing
results and effects on surface or color before proceeding to clean further areas,
ensuring that exactly the same distance and technique are applied as for the test
area. If in doubt, and on sensitive surfaces like fabrics, leather and wood it is always
better to ask for advice from your Steam Cleaner Dealer.
2. For cleaning wood surfaces (furniture, doors, etc...) take great care as too long an
application of steam could alter the waxed appearance, the shine or the color of the
surface cleaned. We therefore recommend you apply steam on such surfaces only
for brief periods or to clean these surfaces using a cloth first held in the steam.
3. Please pay particular attention while cleaning brick floors, too long an application of
steam could damage wax, brightness or color of these surfaces.
4. For delicate surfaces (e.g. synthetic materials, lacquered surfaces etc...), we
recommend that the small brush should always be covered with at least two cloths
to reduce the intensity of the steam.
5. If cleaning glass surfaces in particularly low temperatures pre-heat the glass using
the product from about 50 centimetres distance from the surface to be cleaned.
6. For care of your plants vaporise at a minimum distance of 50 centimetres.
7. The product may be used on its own, without attaching the brushes, for specific
cleaning tasks requiring steam to be applied from a short distance, which will vary
according to the kind of material and the type of soiling to be removed. The more
difficult the soil is to remove, the closer you must hold the product to it, because the
temperature and pressure are higher closer to the steam outlet. In all cases, after
applying steam, wipe the surface with a dry cloth or with a scouring cloth if the soil
is more difficult to remove.
REFILLING THE EMPTY TANK
Whenever the water finishes, unplug the cleaner before adding water.
1. Remove the water tank cap by turning anti clockwise. [1]
2. Fill the measuring jug with normal tap water or demineralised water.
3. Fill the water tank with water. [2]
4. Replace the cap by turning clockwise to lock it.
2
GB
[5]