Publicidad
Idiomas disponibles
Idiomas disponibles
Bedien_3475_0317.ai
Bedien_3475_0317.ai
ENGLISH
①
Lighting unit
②
ON/OFF switch
③
Socket for mains lead
④
Swivel joint
⑤
Fastening socket for 16 mm (5/8") standard spigot
⑥
Dimmer
⑦
Fuse holder
⑧
Wing screw for swivel joint
⑨
Blocking screw for fastening socket
⑩
Illuminated area
⑪
Mains lead
⑫
Distance piece for fabric diffusor
⑬
Screw for distance piece
⑭
Fabric diffusor
Prior to using your light, please read these instructions carefully. Keep
them safe to have them at hand at any time. If you pass the light on to
somebody else, always include these instructions.
1. Intended use
The PL5600 LED Panel Light is intended to be used exclusively for the
illumination of photo and video shots. It is not intended for household
lighting.
Use the light only as described in these instructions. Any other use
has to be considered as not as intended and can result in material
C
damage or physical injury. This light is not a toy.
M
Kaiser Fototechnik takes no responsibility for damages caused by not
Y
intended or incorrect use.
CM
2. Safety instructions
MY
Please observe the following safety instructions:
CY
WARNING!
CMY
Disconnect the light from the mains when not in use or before clean-
ing.
K
Keep the light away from children.
Do not put the light into operation, if housing, cable or plug is dam-
aged.
Do not look directly into the light for a longer period of time, when it is
switched on.
Do not disassemble or modify the light. Repairs must only be carried
out by qualified persons.
CAUTION!
Only use the light with parts designed for it.
Keep the light away from water and other liquids and from combusti-
ble materials.
Make sure that the light is not covered during operation.
Do not use or store the light at places with extremely high air humidity
or at extremely hot places. Keep the light away from long-standing
direct solar radiation.
Let the light cool down before boxing it.
3. Check light and scope of supply
When unpacking the light for the first time, please check if the scope of
supply is complete. It comprises:
- Lighting unit (1)
- Mains lead (11)
- Fabric diffusor (14)
- 4 x distance piece (12), for fabric diffusor
- 4 x screw (13), for distance piece
- 2 x spare fuse
Check also, if the light and the mains lead are damaged by extraneous
causes. Is this the case, do not take the devices into operation.
4
4
08.03.17
08.03.17
16:49
16:49
4. Attaching and tilting the light
The light has to be mounted on a suitable light stand or support with 16 mm
(5/8") standard spigot. Always take care of a safe stand: The center
column of a light stand should be in a vertical position. If the balance point
of the mounted light is outside the direction of the center column, then it
should be directed towards one of the legs of the stand.
Fit the fastening socket (5) on the standard spigot (fig. B) and lock it with
the screw (9). The light can also be operated upside-down in an overhead
position.
The light can be tilted backward and forward by 90° (fig. C). Hold the light
with one hand, loosen the wing screw (8) by rotating it counter-clockwise,
move the light to the desired position and fasten the wing screw (8) again.
5. Initial operation
Check that the mains voltage corresponds to the operating voltage given
on the light.
Take care that the light is switched off: the switch (2) has to be in the OFF
position. Then put the plug of the mains lead (11) into the socket (3) at the
back of the lighting unit (fig. D) and the mains plug into a mains socket.
Push the switch (2) in the ON position.
Brightness can be continuously adjusted by rotating the control dial (6).
The included fabric diffusor (14) can be used to achieve a softer illumina-
tion (fig. E).
Put the switch (2) in the OFF position, when the light is not in use.
The light can be operated for an unlimited time.
6. Changing fuse
Pull out the mains plug before changing a fuse. The fuse can be
replaced after the fuse holder (7) has been unscrewed. The light must
only be run with the specified fuse (F 4 A).
7. Maintenance and care
The light is maintenance-free. Make sure that the front screen (10) is
free of stains and dirt. If necessary remove these before operation.
Clean the light with a soft dry cloth. On no account use petrol or other
solvents.
8. Specifications
Light source:
504 High-CRI LEDs
Color temperature:
5600 Kelvin
Color rendition index:
CRI = 95
Angle of radiation:
110°
Max. illumination:
2300 lux (at 1 m / 3.3 ft.)
Panel size:
40 x 55 cm (15.7 x 21.7 in.)
Power consumption:
100 W
Operating voltage:
100 – 240 V
Fuse:
F 4 A
Dimensions (WxHxD):
400 x 650 x 30-50 mm (15.7 x 25.6 x
1.2 - 2 in.), with swivel joint
Weight:
3 kg (6.6 lbs.)
9. Accessories
3194 "Compact 175" light stand, setting height 45 to 175 cm
3195 "Small" light stand, setting height 75 to 230 cm
3196 "Large" light stand, setting height 110 to 290 cm
3198 Studio stand with 3 castors, setting height 131 to 217 cm
3190 "VarioBase 300" light stand, with leveling legs, setting
height 63 to 298 cm (24.8 to 117.3 in.)
5048 Reversible thread pin 16 mm (5/8"), with 1/4" and 3/8"
mounting threads
5040 "Magic Arm" hinged bracket
5043 Universal clamp with 16 mm (5/8") socket
5570 Clamp base with tiltable mounting socket for 16 mm (5/8")
standard spigot
5847 Mounting socket for accessories with 16 mm (5/8")
standard spigot. 2 pieces
Right reserved to make technical modifications.
All specifications are approximate.
Publicidad
