Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT SAFETY INSTRUCTIONS
When using your iron, basic safety precautions should always be followed, including
the following:
1.
Read all instructions carefully.
2.
Use iron only for its intended use.
3.
To protect against risk of electrical
shock, do not immerse the iron in
water or other liquids.
4.
Never yank cord to disconnect from
outlet. Grasp plug and pull to
disconnect.
5.
Do not allow cord to touch hot
surfaces. Let iron cool completely
before putting away.
6.
Always disconnect iron from electrical
outlet when filling with water, emptying,
or when not in use.
7.
Do not operate iron with a damaged
cord, or after the iron has been
dropped or damaged in any manner.
To avoid the risk of electric shock, do
not disassemble the iron. Return the
iron to EURO-PRO Operating LLC for
examination and repair. Incorrect
reassembly can cause the risk of
electric shock when the iron is used.
8.
Close supervision is necessary for any
appliance being used by or near
children. Do not leave iron unattended
while connected or on an ironing
board.
9.
Burns can occur from touching hot
metal parts, hot water or steam. Use
caution when you turn a steam iron
upside down; there may be hot water
in the reservoir.
10. Never use or rest iron on an unstable
surface.
11. While the iron is hot, never set iron on
an unprotected surface - even if it is on
its heel rest.
12. CAUTION! TO PREVENT ELECTRIC
SHOCK OR OTHER INJURY, before
filling the iron with water, make sure
that the plug is removed from the
outlet.
POLARIZED PLUG:
This appliance has a polarized plug (one blade is wider than
the other). As a safety feature, this plug will fit into a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature.
SAVE THESE INSTRUCTIONS
For Household Use Only
13. WARNING: Never fill the iron with
fabric conditioner, starches or any
other solution, as these will damage
the steam mechanism. Do not use
contaminated water.
14. CAUTION! TO AVOID FIRE, never
leave iron unattended while it is
plugged in.
15. CAUTION! TO PREVENT ELECTRIC
SHOCK, never use the iron in a
location where it can fall or be
pulled into water or another liquid. If
the iron falls into water or other
liquid, unplug it immediately. DO
NOT reach into the water or liquid.
16. WARNING: Never use scouring
pads, abrasive or chemical cleaners,
or solvents to clean the exterior or
soleplate of your iron. Doing so will
scratch and/or damage the surface.
17. CAUTION! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
18. Always store your iron standing
upright, not on the soleplate. If stored
face down, even the smallest amount
of moisture will cause the soleplate to
corrode and stain.
19. This appliance is for household use
only.
SPECIAL INSTRUCTIONS
1.
To avoid a circuit overload, do not
operate another high-wattage
appliance on the same circuit.
2.
If an extension cord is absolutely
necessary, use a 15-ampere cord.
Cords rated for less amperage may
overheat. Use care to arrange the cord
so that it cannot be pulled or tripped
over.
1
REV. 09/07A
GETTING TO KNOW YOUR ELECTRONIC IRON
Before using your Shark Intelligent
Electronic Iron, remove any labels,
stickers or tags that may be attached to
the body or soleplate of the iron.
When turned on for the first time, your
new iron may emit an odor for up to 10
minutes. This is due to the initial
heating of the materials used in making
the iron.
10
2
6
7
8
9
1
4
5
3
1. Electronic Temperature Control
2. Display Panel
3. Atomizer Spray Button
4. Burst of Steam/X-Tended
TM
Steam Burst
Button
5. Variable Steam Control
6. Water Inlet Door
7. Spray Nozzle
Technical Specifications
Voltage:
120V., 60Hz.
Power:
1600 Watts
The odor is safe and should not re-
occur after initial heating. Also, before
ironing with steam for the first time,
allow iron to heat, hold in a horizontal
position and hit the burst of steam
button several times. The iron may
emit some small particles from the
steam holes. This is normal and will
clear after pressing the burst of steam
button several times.
Display Panel
13
12
15
8.
Water Level Window
9.
Stainless Steel Soleplate
10. Handle
11. Auto-Off Light
12. Power Light
13. Fabric & Steam Settings
14. Temperature Indicators
15. Water Flask
2
14
11
Publicidad
Tabla de contenido
