Adjusting The Cutting Height - Bavaria BBC 25/1 Manual De Instrucciones

Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Functions
Vibration emission value a
K uncertainty = 1.5 m/s
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Assembly
5.1.1 Fitting the long handle (Fig. 3)
Using the 4 Allen screws M6x20 (20), fasten the
long handle assembly (2) to the engine assembly
(1).
5.1.2 Fitting the steady grip
Fit the left steady grip (3b) or the right steady grip
(3a) as shown in Figs. 4a-4b. The holes in the
steady grips are for receiving the screws. Tighten
the screws (16) securely at the top part of the
steady grip holder (19).
5.1.3 Fastening the harness and cable
Hook the harness (15) into the holder as shown
in Fig. 8a-8c. Then use the supplied cable ties
(31) to fasten the cable to the long handle and the
steady grip (Fig. 4c).
5.1.4 Fitting the blade guard hood
The cutting blade guard hood must be fi tted if you
wish to work with the cutting blade. The guard
hood for the cutting blade must be installed as
shown in Fig. 5.
5.1.5Fitting/Replacing the cutting blade
The fi tting of the cutting blade is shown in Figures
6a – 6g. To dismantle, proceed in reverse order.
•
Fit the carrier plate (22) onto the spline shaft
(Fig. 6b)
•
Securely fit the cutting blade (18) on the co-
ver ring (Fig. 6c)
Anl_BBC_25_1_SPK7.indb 20 Anl_BBC_25_1_SPK7.indb 20
= 8.57 m/s
2
h
2
- 20 -
GB
•
Place the pressure plate (23) over the thread
of the spline shaft (Fig. 6d).
•
Plug on the cover of the pressure plate (24)
(Fig. 6e).
•
Look for the hole in the carrier plate, line up
with the notch underneath, lock with the sup-
plied Allen key (29), and tighten the nut (25)
(Fig. 6f/6g). Important: Left-hand thread
5.1.6 Fitting the cutting line guard hood to
the blade guard hood
Important: The cutting line guard hood must be
additionally fi tted if you want to work with the cut-
ting line.
The guard hood for the cutting line must be ins-
talled as shown in Figures 7a – 7b.
5.1.7 Fitting/Replacing the line spool
The fi tting of the line spool is shown on Figure 7c.
To dismantle, proceed in reverse order.
Look for the hole in the carrier plate, line up with
the notch beneath it, lock with the supplied Allen
key (29), and screw the line spool onto the thread.
Important: Left-hand thread

5.2. Adjusting the cutting height

1. Slip the harness (Item 17) over your left
shoulder.
2. Hang the petrol power scythe in the harness
(Fig. 8a - 8c).
3. Set a comfortable cutting height by extending
or shortening the harness (Fig. 8d).
4. Secure the position of the harness by threa-
ding the strap through the buckle (Fig. 8e).
5. To establish the optimum length of the har-
ness, you should then make a few swinging
movements without starting the engine (Fig.
8f-9a).
Important: Always use the strap when working
with the equipment. Attach the strap as soon as
you have started the engine and it is running in
idle mode. Switch off the engine before you take
off the carrying strap.
05.11.14 10:25 05.11.14 10:25