Oiler Adjustment; Placing Tool In Service - Ingersoll Rand S80–EU Manual Del Usuario

•
Keep hands and clothing away from the blade. The blade
of a Circular Saw will coast before stopping after the
throttle is released.
•
Do not stop rotation of blade by putting lateral pressure
on it.
•
Operate the Saw only when standing on a stable platform
and holding the Saw with two hands. Do not operate the
Saw while standing on a ladder.
•
Rest the guide plate fully on the workpiece when
operating.
•
Do not force the Saw into the workpiece. The Saw may
kick back if the blade is forced or pinched while making
a cut.

OILER ADJUSTMENT

The built–in lubricator has been properly adjusted at the
factory to produce the correct amount of lubrication for the
tool. Insufficient lubrication can result from clogged oiler
felts within the lubricator. To replace the felts, proceed as
follows:
1. Remove the Oiler Plug and pour the oil from the oil
chamber.
2. Remove the wool from the chamber with tweezers.
3. With a thin blade screwdriver, remove the Oiler
Adjustment Screw.
4. Using tweezers or a bent piece of wire, remove the
Oiler Felts and install a new set.
5. Replace the Oiler Adjusting Screw, installing it slightly
below flush, and replace the wool.
6. Replenish the oil supply.
LUBRICATION
Ingersoll–Rand No. 50
Always use an air line lubricator with these tools. We
recommend the following Filter–Lubricator–Regulator
Unit:
For International – No. FRL30–C6–A29
Where a permanent lubricator cannot be installed,
inject 1.5 cc of Ingersoll–Rand No. 50 Oil into the air inlet
before attaching the hose. Remove the Oiler Plug from the
Motor Housing and fill the chamber.
After each eight hours of operation, replenish the oil
supply. Periodically, lubricate the Bevel Bracket, Depth
Bracket and all slides and pivots with Ingersoll–Rand
No. 28 Grease or a light oil.
SAW SPECIFIC WARNINGS (Continued)

PLACING TOOL IN SERVICE

Ingersoll–Rand No. 28
Ingersoll–Rand No. 100
•
Always use genuine Ingersoll–Rand Flanges provided
with the Saw. Never use a substitute.
•
Mount the blade and flanges as instructed in this manual.
Always mount the blade so that the arrow on the blade
and the arrow on the Swing Guard point in the same
direction.
•
Never operate the Saw without the Flange Retaining
Screw installed in its proper place in the end of the
Arbor. Always securely tighten the Flange Retaining
Screw as instructed in this manual before operating the
Saw.
•
Do not use saws in a bench mounted configuration.
Fill an empty Gear Case with 3 cc of Ingersoll–Rand
No. 28 Grease, and replenish the supply after every six
months, whichever occurs more frequently.
After each year of service, clean all grease from the Gear
Case and replace it with 3 cc of fresh Ingersoll–Rand
No. 28 Grease.
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
REGULATOR
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
CONTROLLER INFORMATION
Do not attempt to disassemble the Controller.
The Controller is available only as a unit and is guaranteed
for the life of the tool if it is not abused.
Prior to assembly, carefully inspect the Controller
Assembly for nicks, gouges and dents. Replace it with a
new Controller Assembly if necessary. Test the free speed
before applying a blade.
3
FILTER
COMPRESSOR
(Dwg. TPD905–1)