Oiler Adjustment; Placing Tool In Service - Ingersoll Rand S80 Manual De Funcionamiento

•
Keep hands and clothing away from the blade. The
blade of a Circular Saw will coast before stopping
after the throttle is released.
•
Do not stop rotation of blade by putting lateral
pressure on it.
•
Operate the Saw only when standing on a stable
platform and holding the Saw with two hands. Do
not operate the Saw while standing on a ladder.
•
Rest the guide plate fully on the workpiece when
operating.
•
Do not force the Saw into the workpiece. The Saw
may kick back if the blade is forced or pinched
while making a cut.

OILER ADJUSTMENT

The built–in lubricator has been properly adjusted at the
factory to produce the correct amount of lubrication for the
tool. Insufficient lubrication can result from clogged oiler
felts within the lubricator. To replace the felts, proceed as
follows:
1. Remove the Oiler Plug and pour the oil from the oil
chamber.
2. Remove the wool from the chamber with tweezers.
3. With a thin blade screwdriver, remove the Oiler
Adjustment Screw.
4. Using tweezers or a bent piece of wire, remove the
Oiler Felts and install a new set.
5. Replace the Oiler Adjusting Screw, installing it slightly
below flush, and replace the wool.
6. Replenish the oil supply.
LUBRICATION
Ingersoll–Rand No. 50
Always use an air line lubricator with these tools. We
recommend the following Filter–Lubricator–Regulator
Unit:
For USA – No. C31–06–G00
Where a permanent lubricator cannot be installed,
inject 1.5 cc of Ingersoll–Rand No. 50 Oil into the air inlet
before attaching the hose. Remove the Oiler Plug from the
Motor Housing and fill the chamber.
After each eight hours of operation, replenish the oil
supply. Periodically, lubricate the Bevel Bracket, Depth
Bracket and all slides and pivots with Ingersoll–Rand
No. 28 Grease or a light oil.
SAW SPECIFIC WARNINGS (Continued)

PLACING TOOL IN SERVICE

Ingersoll–Rand No. 28
Ingersoll–Rand No. 100
•
Always use genuine Ingersoll–Rand Flanges
provided with the Saw. Never use a substitute.
•
Mount the blade and flanges as instructed in this
manual. Always mount the blade so that the arrow
on the blade and the arrow on the Swing Guard
point in the same direction.
•
Never operate the Saw without the Flange
Retaining Screw installed in its proper place in the
end of the Arbor. Always securely tighten the
Flange Retaining Screw as instructed in this manual
before operating the Saw.
•
Do not use saws in a bench mounted configuration.
Fill an empty Gear Case with 3 cc of Ingersoll–Rand
No. 28 Grease, and replenish the supply after every six
months, whichever occurs more frequently.
After each year of service, clean all grease from the Gear
Case and replace it with 3 cc of fresh Ingersoll–Rand
No. 28 Grease.
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
REGULATOR
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
CONTROLLER INFORMATION
Do not attempt to disassemble the Controller.
The Controller is available only as a unit and is guaranteed
for the life of the tool if it is not abused.
Prior to assembly, carefully inspect the Controller
Assembly for nicks, gouges and dents. Replace it with a
new Controller Assembly if necessary. Test the free speed
before applying a blade.
3
FILTER
COMPRESSOR
(Dwg. TPD905–1)