Cleaning, Maintenance And Ordering Of Spare Parts - HERKULES AHW 2500 Manual De Instrucciones

Anleitung_AHW_2500_SPK7:_
8.3 The lifting forks do not descend when the
control lever is in the lowering position
(Fig. 5) Turn the hex nut (K) on the setting screw (H)
clockwise to the point where the lifting forks are
lowered by pulling up the control lever. Then check
the operation of the traveling position in order to
guarantee that the setting nut is in the correct
position.
8.4 The lifting forks do not rise when the control
lever is in the lifting position
(Fig. 5) Turn the hex nut (K) on the setting screw (H)
counter-clockwise to the point where the lifting forks
are raised when the control lever is in the lifting
position. Then check the operation of the traveling
position and the lowering position in order to
guarantee that the setting nut is in the correct
position.
9. Cleaning, maintenance and ordering
of spare parts
9.1 Cleaning
Use a damp cloth to clean the casing.
9.2 Servicing
The pallet lifting truck must be regularly inspected
and if necessary serviced in order to keep it in good
working order. All the repair and maintenance jobs
which are not listed here must be carried out by a
customer service center or an authorized specialist.
This applies in particular to replacing the steering and
load-bearing rollers.
If malfunctions arise, the pallet lifting truck must be
taken out of operation immediately and be repaired
by an authorized person. Only original spare parts are
allowed to be used.
The pallet lifting truck must be inspected by an expert
at least once a year or more often if necessary. It is
recommended to record the inspections in an
inspection book.
After carrying out repair or maintenance work, ensure
that all safety parts are installed and in perfect
condition.
Store potentially hazardous parts out of the reach of
other persons and children.
Important: In accordance with the German Product
Liability Act, we are not liable for any damages if they
result from improper repairs to the product or if parts
are replaced by items other than genuine parts or
parts approved by us. Furthermore, we are not liable
for any damages if they result from improper repairs
22.08.2011 13:26 Uhr Seite 11
to the product. Arrange for your customer service or
an authorized workshop to do the work. The same
applies to accessory parts.
9.2.1 Filling up with hydraulic oil
Check the oil level every six months. When filling up
with hydraulic oil or replacing it, use only hydraulic oil
from the viscosity classes HLP 46 (- 20 °C - + 40°C) .
A complete filling equals approx. 0.4 liters.
Important! To prevent environmental contamination
from escaping oil, use absorbent materials (e.g. wood
chips, dry rags) promptly to pick up any oil spills.
Take soiled maintenance material and operating
materials to an appropriate collection point and
dispose of the soiled material correctly.
1. Lower the lifting forks as far as possible
2. Remove the oil filler plug and seal from the oil
tank.
3. Fill in hydraulic oil up to the brim
4. Reinsert the oil filler plug and seal into the oil
tank.
5. Vent the hydraulics system with several pumping
movements of the drawbar
9.3 Venting the hydraulic unit
If the lifting forks do not rise when the control lever is
in the lifting position, move the control lever into the
lower position and move the drawbar up and down
again several times.
9.4 Lubricating the moving parts
Lubricate and grease the moving parts regularly.
9.5 Ordering spare parts
Please provide the following information on all orders
for spare parts:
Model/type of the equipment
Article number of the equipment
ID number of the equipment
Part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
10. Storage
If you are not going to use the pallet lifting truck for a
long time, store it under covers and out of children's
reach in a dark and dry place at above freezing
temperature after you have cleaned it thoroughly and
lubricated it. The ideal storage temperature is
between 5 und 30 °C.
GB
11