Bosch BSG6 Serie Instrucciones De Uso página 39

Emptying the dust filter
To achieve an optimal result when vacuuming, the dust
container should be emptied each time the vacuum cleaner
is used.
19
Figure
Turn the dust compartment locking lever in the direction
of the arrow to open the dust compartment cover.
20
Figure
Remove the dust container from the appliance.
21
Figure
Release the two snap locks on the bottom flap in the
direction of the arrow, open the flap until it clicks into the
stop position and the container will then empty the dirt in
a downwards direction.
If the bottom flap is very dirty, (thick dirt) clean it before
closing, by vacuuming it with the crevice nozzle, for
example.
(You must fit the dust bag in the vacuum cleaner
when you do this - see Figure 26)
Close the bottom flap so that it can be heard snapping
into position.
22
Figure
Put the dust bag back into the vacuum cleaner and close
the dust bag compartment lid.
Caution: The inside of the dust container may
!
become scratched with use and start to look opaque.
This does not, however, affect the performance of the
vacuum cleaner in any way, i.e. it will continue to
function as normal.
Cleaning the permanent filters and
micro filters in the dust container
The filters must be cleaned:
After any operating malfunctions, i.e. after a blockage is
cleared.
At least every six months.
23
Figure
Press the fastener on the rear side of the container and
remove the micro filter from the bottom of the container.
Remove the permanent filter from the bottom plate of the
container.
24
Figure
Wash the micro- and permanent filters.
The filter must then be left to dry for at least 24 hours.
After cleaning, place the permanent filter on the bottom
plate of the container.
Put the micro filter onto the container and fix it in place
by pushing in the direction of the arrow. You will hear the
flap snap shut.
* Depending on equipment
38
Blockages
Removing a blockage in the dust container.
25
Figure
Empty the container (see figure 21)
Loosen the blockage, e.g. with a screwdriver, and tap or
vacuum it out.
(You must fit a dust bag in the vacuum cleaner before
vacuuming it out - see Figure 26)
Close the bottom flap so that it can be heard snapping
into position.
Caution: The micro- and permanent filters must be
!
cleaned following any operating problem (see Figure
23 and 24).
Using dust bags
If desired, a dust bag may be used instead of the dust
container.
26
Figure
Open the dust bag compartment lid.
Remove the dust container and insert a dust bag.
Close the vacuum cleaner lid.
You have bought an extremely powerful device.
The highest suction setting is therefore only recommended
for heavily soiled, short-pile carpets and hard floors.
The required suction power can be selected by adjusting
the suction regulator (see Figure 9).
Low suction range:
For vacuuming delicate fabrics, e.g. curtains.
Middle suction range:
For daily vacuuming of lightly soiled floors.
High suction range:
For vacuuming durable floor coverings, hard floors and
for heavily soiled surfaces.
Replacing the dust bag
27*
Figure
a) If the dust bag change indicator is completely yellow
when the floor tool is lifted from the floor and the highest
suction power is selected, the dust bag needs changing.
Even if the dust bag is not full, it may still need changing,
due to the type of dust which has been vacuumed.
First check that the nozzle, suction pipe and flexible tube
are not blocked, as this would also lead to dust bag
change indicator being triggered.
b) The handle can easily be detached from the hose to
remove blockages.
28
Figure
Open the lid by moving the locking lever in the direction
of the arrow.
29
Figure
a) Seal the dust bag by pulling the sealing strip and then
remove it.
b) Slide the new dust bag into the holder to the stop.
Caution: The lid can only be closed when a dust bag has
!
been inserted.