Inglesina Wave Manual De Instrucciones página 18

solid urban waste cycle, but collected separately in order
to optimize the recovery and recycling flow of the materials
they contain, while also preventing potential damage
to human health and the environment arising from the
presence of potentially hazardous substances .
The crossed out bin symbol is printed on all products as a
reminder.
Waste may be taken to special collection site or can be
delivered free of charge to the dealer when purchasing a new
equivalent or without obligation to make a new purchase for
equipment smaller than 25 cm.
For more information on proper disposal of these devices,
kindly refer to the public utility service.
LIST OF COMPONENTS
fig. 1
A Left support
B Right support
C Front and rear base
D Swing Cover + seat structure
E Adapter
F Toy bar
G Electronic device
H AC/DC Transformer
K Auxiliary audio interface cable
STRUCTURE ASSEMBLING
fig. 2 After removing the protections from the metal
pins (A3), press the button (A1) and open out the left swing
support (A) until it clicks, locking into place.
Then repeat the operation for the right support (B).
fig. 3 Insert the base (C) on the back leg and, holding
down the button (C1), complete installation by pushing it
into the housing until you clearly hear it click correctly into
place.
fig. 4 Repeat the operation for the front base and
complete swing structure assembly.
fig. 5 Open out the seat structure complete with cover
(D).
fig. 6 To secure the seat to the structure, position the
support (D1) on the side joint (A2) and, making sure that the
metal pin (A3) engages correctly in the hole (D2) in the joint,
complete the attachment by pushing the support (D1) into
the housing, until it clicks correctly into place.
fig. 7 Repeat the operation also for the other joint and
finish securing the seat to the structure.
TOY BAR
fig. 8 To fix the toy bar (F), engage both couplings (F1)
with the dedicated supports (F2).
CAUTION! Never use the toy bar to carry the reclined
cradle.
fig. 9 The toys can be detached and repositioned easily
(also for the purposes of correct maintenance) by removing
them from their housings on the bar.
SEAT INCLINATION
fig. 10 By pressing both buttons (D3), the seat inclination
can be adjusted to 2 different positions.
SEAT POSITIONS
fig. 11 Position
Position
ROCKING
fig. 12 Use the lever (D4) to lock the rocking motion of the
18
• Transformer used with the infant swing is to be regularly
examined for damage to the cord, plug, enclosure and other
parts, and in the event of such damage, it shall not be used.
• The transformer is fit for use with the following supply
voltages: 100-240V ~ 50/60 Hz.
• When the swing is used connected to the domestic mains,
with the transformer provided, pay attention to the hazards
that arise from the use of electricity. Always strictly follow the
electrical safety regulations in force in your country.
• Each time you finish using the swing, switch off the
electronic device and, if used, disconnect the transformer
and any other external music devices.
INSTRUCTIONS
swing.
Caution: do not use the locking lever (D4) when the swing
is in motion.
Warning! Always block the rocking motion before
settling and/or removing the child.
ADAPTER
fig. 13
standard.
SAFETY BELTS
WARNING! Always use the restraint system.
fig. 14
at shoulder level or just above. If the position is not correct,
remove them and reinsert them in another pair of slots;
always use slots at the same height.
fig. 15
in the ends of the waist one.
fig. 16
buckle.
fig. 17
loops (D5) and, when being used, it must be adjusted in
order to properly secure the baby.
fig. 18
one, adjusting both of them properly.
CAUTION! Failure to comply with this precaution can
cause the baby to fall or slide out, with serious injury
risks.
FUNCTIONS AND USE OF THE ELECTRONIC DEVICE
The electronic device operates either with the transformer
provided or with 4 AA-type 1.5-volt batteries (not included).
fig. 19
(H) in the main socket (A4) on the left swing support (A).
fig. 20
the device, removing the screw (G2) using a cross-head
screwdriver (not included).
fig. 21
batteries.
fig. 22
screws (G2).
fig. 23
adjust the rocking speed
timer (after 8, 15 or 30 minutes)
type and volume of the melodies available .
fig. 24
(A5) that allows an external device to be connected through
the dedicated cable (K) provided.
CLOSING
When not in use, the swing can easily be closed and put away.
fig. 25
The swing comes with adapter cushion (E) as
Check that the belts have been fitted in the slots,
Make sure that the back strap is properly inserted
Fasten the ends of the strap belt to the central
The waist strap must always pass through the side
Always use the crotch strap together with the waist
Insert the jack connector (H1) of the transformer
To insert the batteries, open the cover (G1) on
Observe the polarity indicated when inserting the
Close the cover again (G1) using the dedicated
Use the keypad on the electronic device (G) to
, set the rocking and music sleep
, as well as to select the
The Wave swing features an auxiliary audio input
To close correctly, firstly fold up the seat (D).