Hitachi DH 38MS Instrucciones De Manejo página 3

DEMOLITION HAMMER SAFETY
WARNINGS
1. Wear ear protectors.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
5. Before starting to break, chip or drill into a wall, fl oor or
ceiling, thoroughly confi rm that such items as electric
cables or conduits are not buried inside.
6. Always hold the body handle and side handle of the
power tool fi rmly. Otherwise the counterforce produced
may result in inaccurate and even dangerous operation.
7. Wear a dust mask.
Do not inhale the harmful dusts generated in drilling or
chiseling operation. The dust can endanger the health of
yourself and bystanders.
8 Ensure that the wing bolt in the side handle is properly
tightened before using the tool.
9 Although this machine is equipped with a safety clutch, if
the drill bit becomes bound in concrete or other material,
the resultant stoppage of the drill bit could cause the
machine body to turn in reaction. Ensure that the
main handle and side handle are gripped fi rmly during
operation.
10 If the selector lever is switched during motor rotation, the
tool can start to rotate abruptly, resulting in unexpected
accidents. Make sure to switch the selector lever when
the motor is at a complete stop.
11 If the bull point or cold chisel is used at the position of
"rotation + hammering", the tool can start to rotate,
resulting in unexpected accidents. Make sure that they
are used at the position of "hammering".
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
DH38MS : Rotary Hammer
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
Switching OFF
Hammering only function
Adjustment of the tool position function
Rotation and hammering function
Disconnect mains plug from electrical outlet
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
○ Case .............................................................................1
○ Side Handle ..................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Drilling holes in concrete
○ Drilling anchor holes
○ Demolishing concrete, chipping, digging, and squaring
(by applying optional accessories)
SPECIFICATIONS
Voltage (by areas)
Power Input
Capacity
No-load speed
Full-load Impact Rate
Weight
(without cord, side handle)
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
3
English
(110 V, 120 V, 127 V,
220 V, 230 V, 240 V)
950 W
Drill bit : 38 mm
Core bit : 105 mm
620 min
-1
2800 min
-1
6.4 kg