Unpacking And Checking; Unit Identification - Stulz COSMOTEC CVE Serie Manual De Uso Y Mantenimiento

can't be installed on mobile part, on devices/parts that transfer can't be installed on mobile part, on devices/parts that transfer
vibration, oscillating parts, inclined parts (not levelled). In general air vibration, oscillating parts, inclined parts (not levelled). In general air
conditioners can't be installed on following situations: zone strong oners can't be installed on following situations: zone strong
heat radiation, with strong magnetic fields, with free flames, with heat radiation, with strong magnetic fields, with free flames, with
fire risk, with inflammable products, with explosive atmosphere, fire risk, with inflammable products, with explosive atmosphere,
with saline atmosphere, with aggressive atmosphere. For any doubt, with saline atmosphere, with aggressive atmosphere. For any d
please consult the manufacturer.
ATTENTION!
Before each opening of enclosure, where one or more air Before each opening of enclosure, where one or more air
conditioners are installed, it is necessary to switch off power conditioners are installed, it is necessary to switch off power
supply of unit
If there are traces of oil on the unit, indicative of a leak of coolant, If there are traces of oil on the unit, indicative of a leak of coolant,
inside or outside, inspect the equipment carefully before switching inside or outside, inspect the equipment carefully before switching
on and possibly consult STULZ SpA technical department.
Do not operate the unit if there is a leak of coolant. Do not operate the unit if there is a leak of coolant.
LABEL ON THE UNIT
DANGER: HOT COMPONENTS

3. UNPACKING AND CHECKING

STULZ SpA products are shipped free ex works
individually checked throughout and carefully packed. Check the individually checked throughout and carefully packed. Check the
unit on arrival, ensuring that it has been transported in the correct unit on arrival, ensuring that it has been transported in the correct
position. If this is not the case, make a note on the delivery position. If this is not the case, make a note on the delivery
documents. It is advisable to accept the goods subject to inspection.
Check for the absence of any damage or oil spots. If these are noted, Check for the absence of any damage or oil spots. If these are noted,
immediately make a note on the delivery document. Remove the immediately make a note on the delivery document. Remove the
packing and check that the outer casing has not been hit, scratched packing and check that the outer casing has not been hit, scratched
or shows any other marks. Check for any missing parts. Before marks. Check for any missing parts. Before
disposing of the packing materials, make sure they there are no disposing of the packing materials, make sure they there are no
other documents or machine parts in them. The haulier must be other documents or machine parts in them. The haulier must be
informed of any damage by means of a recorded delivery letter informed of any damage by means of a recorded delivery letter
within 8 days of receipt of the product.
The haulier is responsible for any damage occurring during The haulier is responsible for any damage occurring during
transport.
STULZ SpA will not be held liable for damage caused by the hauliers will not be held liable for damage caused by the hauliers
equipment, although it will offer assistance should the need arise. equipment, although it will offer assistance should the need arise.
N.B. The product cannot be returned without the prior written
approval of STULZ SpA
For any assistance, contact:
STULZ SpA – CUSTOMER SERVICE
Via Torricelli, 3 37067 Valeggio sul Mincio (VR) Italy 37067 Valeggio sul Mincio (VR) Italy
Tel. (++39)(0) 45 6331615 / Fax. (++39)(0) 45 6331635 Tel. (++39)(0) 45 6331615 / Fax. (++39)(0) 45 6331635
E-mail: aftersales@stulz.it
NB: If the product cannot be installed immediately or needs to be NB: If the product cannot be installed immediately or needs to be
transported to its final destination, after checking it should be transported to its final destination, after checking it should be
repacked in its original packing and stored in a protected locat repacked in its original packing and stored in a protected location.
Storage limits: temperature (min:-40°C, max:+60°C), humidity (max
90%, not condensing).
technical department.
free ex works. All the units are
e goods subject to inspection.
returned without the prior written
40°C, max:+60°C), humidity (max
In order to protect the environment, separate the plastic materials In order to protect the environment, separate the plastic materials
and recycle the cardboard packaging. and recycle the cardboard packaging.
4. PRECAUTIONS WHEN HANDLING THE UNIT 4. PRECAUTIONS WHEN HANDLING THE UNIT
To operate this unit when packed, use a fork lift or a system with operate this unit when packed, use a fork lift or a system with
straps or ropes.
When unpacked, refer to the weight of the unit reported on its When unpacked, refer to the weight of the unit reported on its
identification plate. The unit must be handled using the appropriate identification plate. The unit must be handled using the appropriate
lifting devices inserting the eyebolts ( lifting devices inserting the eyebolts (M6/M8) in the prearranged
holes.

5. UNIT IDENTIFICATION

Depending on the model chosen, cooling unit may vary in Depending on the model chosen, cooling unit may vary in
appearance/data from the illustrations contained in these appearance/data from the illustrations contained in these
instructions. The unit can be identified from the identification plate he unit can be identified from the identification plate
which contains information required for its identification and ns information required for its identification and
correct use. The identification plate is hot pressed onto a plastic correct use. The identification plate is hot pressed onto a plastic
support, making the text almost indelible even in harsh support, making the text almost indelible even in harsh
environments.
N.B. The serial number must be provided when requesting The serial number must be provided when requesting
information or for any other needs regarding the unit. or for any other needs regarding the unit.
21
CVE-CVO
ATTENTION! ATTENTION!