Preface
This manual is intended for fitters who are to install
and maintain the ComfoCool Q600.
The ComfoCool Q600 is only intended for use in
combination with the ComfoAir Q600 ST (hencefort
called "heat-recovery unit").
� The ComfoCool Q600 is fitted on top with an
identification plate.
1 Warranty and liability
Warranty conditions
The ComfoCool Q600 is covered by a manufacturer's
warranty for a period of 24 months after fitting up to a
maximum of 30 months after the date of manufacture.
Warranty claims may only be submitted for material
faults and/or construction faults arising during the
warranty period. In the case of a warranty claim, the
ComfoCool Q600 must not be dismantled without
written permission from the manufacturer. Spare parts
are only covered by warranty if they were supplied by
the manufacturer and were installed by an approved
fitter.
The warranty becomes invalid if:
■ Parts are used which were not supplied by the
manufacturer.
■ Unauthorised alterations and/or modifications have
been made to the unit.
■ The warranty period has elapsed.
■ Installation has not been carried out according to the
applicable regulations;
■ The defects are due to incorrect connection, inexpert
use, or contamination of the system;
On-site (dis)assembly costs are not covered by the
terms of the warranty. This also applies to normal
wear and tear. Zehnder retains the right to change the
construction and/or configuration of its products at any
time without being obliged to alter previously delivered
products.
Liability
The ComfoCool Q600 has been designed and built to be
used in combination with the ComfoAir Q600 ST heat-
recovery unit.
Any other application is seen as inappropriate use
and can result in damage to the ComfoCool Q600 or
personal injury, for which the manufacturer cannot
be held liable. The manufacturer is not liable for any
damage derived from:
■ Non-compliance with the safety, assembly, set-
up, maintenance and operating instructions in this
manual.
■ The use of components not supplied or
recommended by the manufacturer.
EN - 24
■ Responsibility for the use of such components lies
entirely with the fitter.
■ Normal wear and tear.
2 Safety regulations
Always comply with safety regulations in this manual.
If the safety regulations, warnings, comments and
instructions are not complied with, this can lead to
personal injury or damage to the ComfoCool Q600.
■ Only registered fitters are permitted to assemble, fit,
commission and set up the ComfoCool Q600, unless
otherwise indicated in this manual.
■ Only a recognised cooling-technology fitter is
permitted to carry out work on the cooling skid.
■ The ComfoCool Q600 must be fitted in accordance
with the general and locally applicable construction,
safety and installation instructions of the local council,
electricity and water boards or other agencies, such
as the relevant national home-building association.
■ Always follow the safety regulations, warnings,
comments and instructions given in this manual.
■ The ComfoCool Q600 contains coolant R134a.
This is a non-flammable, non-toxic coolant. Handle
the cooling skid with great care during installation
or maintenance activities to prevent coolant from
leaking. Anyone involved in maintenance, repair or
recycling of the product should wear gloves and eye
protection at all times.
■ When welding or soldering in the vicinity of the
coolant, always wear breathing equipment fitted with
a filter. The filter should provide protection against
eventual decomposition products.
■ If coolant leaks in anyway due to a defect or damage,
then:
■ Open windows and doors in the room in which the
ComfoCool Q600 is located for at least an hour;
■ The ComfoCool Q600 contains 0.5kg (at room
temperature approx. 0.2m
■ The coolant is heavier than air and will concentrate on
the floor;
■ Never try to contain the escaped gas and do not
breath it in;
■ In the event of skin or eye contact, rinse for at least
20 minutes with lukewarm water, and contact your
doctor.
) coolant;
3