Adjusting The Handles - Peg-Perego book Instrucciones De Uso

EN_English
WARNING
_ IMPORTANT: Keep these instructions for future
reference. Read and keep them for safety use.
The child's safety could be at risk if these
instructions are not followed.
_ This product was designed for the transport of 1 child
in the seat.
_ Do not use this product for a number of occupants
greater than that intended by the manufacturer.
_ This product is approved for children from birth up to
a weight of 15 kg in the seat.
_ For new born babies is recommended to use the
backrest in the most reclined position
_ This product was designed for use in combination
with Peg Perego Ganciomatic products : with "Primo
Viaggio" car seat (0+ group) is approved for children
from birth up to 13 kg of weight
_ When used in combination with car seat, this vehicle
does not replace a cot or a bed.
Should your child need to sleep, then it should be
placed in a suitable pram body, cot or bed.
_ WARNING Check that the pram body or seat unit or
car seat attachment devices are correctly engaged
before use.
Check that the Peg Perego Ganciomatic product are
correctly fixed to the item.
_ WARNING The assembly and preparation of the
product must be carried out by an adult.
_ Do not use this product if there are parts missing or
signs of breakage.
_ WARNING Always use the restraint system. Always
use the five point harness. Always use the harness
crotch strap in combination with the waist strap.
_ WARNING Never leave your child unattended.
_ Always apply the brake when stationary.
_ WARNING Ensure that all the locking devices are
engaged before use.
_ WARNING To avoid injury ensure that your child is
kept away when unfolding and folding this product.
_ WARNING This product is not a toy. Do not let your
child play with this product
_ Do not insert fingers into the mechanisms.
_ Be careful not to hurt the child when adjusting the
mechanisms (handlebar, backrest ... ).
_ Any weights hanging on the handlebar or
handles could make the item unstable; follow the
manufacturer's instructions regards the maximum
loads transportable.
_ The front bar (if present) is not designed to support
the child's weight. It is not designed to keep the child
in the seat and does not substitute for the waist belt.
_ Do not load the baskets over 5Kg. Do not put weight
in the cup holder (if present) in excess of those
indicated on the cup holders themselves and never
hot drinks. Do not put loads of more than 0.2 Kg in
the hood pockets (if present).
_ Do not use the product near to stairs or steps, heat
sources, naked flames or dangerous objects within
reach of the child.
_ Only replacement parts supplied or recommended by
the manufacturer/distributor shall be used.
_ WARNING Don't use the rain cover (if present)
on a product without a hood or parasol that can
hold it. Always use the rain cover only under adult
supervision. Don't use the rain cover indoors and
check to ensure the child is not to warm; do not
park the vehicle close to heat sources and keep well
away from the lighted cigarettes. Ensure that the rain
cover is not interfering with any moving parts of the
carriage/stroller. Always remove the rain cover before
folding your carriage/stroller.
_ WARNING This product is not suitable for running or
skating.
_ Always apply the brake when loading or unloading
children.
_ WARNING Do not add any mattress are not approved
by the manufacturer
The images referring to the textile details may differ
from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS FOR USE
1 OPENING THE STROLLER: to open the stroller, rotate it as
shown. Stroller open.
2 For safety, check the seat is properly attached, as
shown in the picture.
3 Position the brake bar as shown in the figure, and hook
it to the stroller's frame until it clicks into place.
4 ATTACH THE REAR WHEELS to the brake bar as shown,
until they click into place.
5 ATTACH THE FRONT WHEELS to the stroller frame as
shown, until they click into place.
Stroller with wheels fitted properly.
6 ATTACHING THE MAIN HANDLE: if the handle tube
faces upwards, align it with the stroller (Fig_a).
Fasten the handle to the frame as shown in the figure
(Fig_b).
To complete the operation, press the two side buttons
on the handle (Fig_c) to ensure the handle pushes in
all the way, until it clicks into place (Fig_d).
7 FITTING THE BASKET: if lowered, lift the basket tube
to the horizontal position. Press the silver buttons
under the metal basket tube located at the back of
the stroller (fig_a) and remove the metal tube (fig_b).
Thread the tube through the fabric loop on the back
of the basket, making sure that the two silver buttons
are facing downward (fig_c). Re-attach the tube to the
housings (fig_d).
8 Secure the two upper basket vinyl eyelets to the two
grey buttons on either side of the metal tube housing
(fig_e). Remove the cardboard from the lower rear
bar.
IMPORTANT! Secure the two lower basket vinyl
eyelets to the two grey buttons on the top of the
lower rear bar. Please note that the eyelets open
(fig_f).
WARNING! If this operation is not performed correctly,
the basket will not properly hold the weight.
Attach the basket tabs to the grey buttons on the
front of the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS VIDEO AT:
WWW.PEGPEREGO.COM
9 LOCKABLE SWIVEL FRONT WHEELS:
For swivelling wheels, lower the lever (arrow 1). For
fixed wheels, move the lever in the opposite direction
(arrow 2). We recommend using fixed wheels on rough,
uneven surfaces (fig_a).
BRAKE: to set the brakes on the stroller, lower the
levers on the rear wheels with your foot (fig_b). To
release the brakes, lift the lever.
Always set the brakes when the stroller is not moving.
10 ADJUSTING THE HANDLES: the handles can be set into
4 different positions. For the highest position, push the
side buttons and lift the handle upwards at the same
time. Release the buttons. To lower the handles, do the
opposite .
11 HOOD: to assemble the hood, fasten the hood's side
attachments onto the sockets until they click (fig_a);
expand the hood frame so that the fabric is fully
stretched (fig_b).
12 Button the hood onto the stroller's backrest (fig_c), on
both sides and inside the handle (fig_d).
To remove the hood: unfasten the hood's side
attachments from the chassis by pressing the external
button (as shown in fig_e) and unbutton it from the
backrest, the sides of the stroller and inside the handle.
13 The hood has a fabric loop, for tying toys (fig_a).
- 18 -