Technical Details; Product Description - Otto CSG II SERIE Manual Del Usuario

USER'S INSTRUCTIONS FOR CSG II SERIES MODELS: 210 - 245 - 270 - 370 - 400 - 450 - 660 - 1100
2
12
3
5
2
* The various products are differentiated by the tube length and the extruded product type.

1.1. Technical details

#
Model Basic Cartridge
setup
-
CSG II 210
For
CSG II 245
soft-pack
- -
CSG II 270
For
CSG II 370
soft-pack
- -
CSG II 400
For
CSG II 450
cartridge
- -
CSG II 660
- -
CSG II 1100
# Basic setup: It is the mode with which the gun is assembled at the factory and provided to the client.
* Cartridge based conversion kit: plastic spacer with gasket (included in the supply).
** Bag based conversion kit: bag holder, tube scraper, piston collecting soft-pack, soft-pack awards cone (included in the supply).
1.2. Noise emissions and vibrations
When releasing the lever, the level of equivalent A-weighted sound pressure, measured at a 50 cm. horizontal distance during
the application of a sealant and with a gun feeding pressure of 6 Bar / 87 PSI is > 80 dBA. Therefore the use of ear defenders is
recommended. The hand/arm system vibration level was detected on an equivalent model and it is less than 2,5 m/g2.
1.3. Storage
The applicator is supplied in a single KEB WHITE ST/B343 cardboard box, with a 2.8-3 mm. thickness low flute; the gun is held in a
polyethylene bag. Keep at a temperature between -5°C and 45°C, with ambient humidity not exceeding 70%.
Never remove the pressure reducer from the machine in an attempt to increase the inlet pressure. The applicator is
safe up to 10 bar 145 PSI. Do not use any other expedient to increase the pressure.
To properly use the applicator, with one hand, hold the back of the material tube up against the nut and with the
other, grasp the grip to operate the control lever.
English
9
7
1
4
6
10
1
8
9
7
Soft-pack Soft-pack
Cartridge
(ml)
≤ 310
-
≤ 310
-
≤ 310
-
≤ 310
-
-

1. PRODUCT DESCRIPTION

D
8
1)
2)
3)
4)
2 5)
6)
3 7)
8)
9)
10) CE mark
4
11) Exhaust air outlets
5
6 12) Safety hole
FAC-SIMILE
PNEUMATIC APPLICATOR
mod. - xxx/xxx xx - cod. xxxxxxx
P.M.T. srl con unico socio
Via G.Marconi 3/7 - 24051 Antegnate (BG) ITALIA
MAX PRESSURE 10 bar (145 psi)
L H
(ml) (mm) (mm)
260 263
-
≤ 400 307 263
≤ 400 307 263
≤ 600 410 263
≤ 600 440 263
≤ 400 556 263
700 665 263
1800 1150 263
8
Body of the Applicator
Front ring nut
Control lever
Handle
Pressure regulator
Feeding: ¼ gas male threaded connector
Material holder tube
Dump valve
Rear ring nut
mese - anno
D Net Total
Weight (g)
(mm) Mass (g)
78 705 1045
78 1125 1420
78 1100 1395
78 1300 1565
78 1100 1365
78 1300 1660
78 1270 1570
78 1700 2030
Connec- Pressure
tion Maxim
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi
1/4"GAS 10 Bar
maschio 145 psi