EINHELL TC-SM 2534 Dual Manual De Instrucciones Original página 38

3. Safe operation
•
Select a suitable blade for the material you
wish to saw.
•
Never use the drag, crosscut and miter saw to
cut any materials other than those specified
by the manufacturer.
•
Use only the transport devices to move the
machine. Never use the guards for handling
or moving the machine.
•
Use the saw only if it is in perfect condition
and properly maintained.
•
When cutting miters, make sure that the
device for swiveling the arm is fastened se-
curely.
•
The floor around the machine must be level,
clean and free of loose particles, such as
chips and cutting residues.
•
Make sure the workplace and the room are
sufficiently illuminated.
•
The operator must receive proper training
in the use, adjustment and operation of the
machine.
•
Only use properly sharpened saw blades. Do
not exceed the maximum speed specified on
the blade.
•
Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for
the intended purpose.
•
If the machine is equipped with a laser, this
laser may not be replaced by a different type
of laser. Repairs may only be carried out by
the manufacturer of the laser or one of his
authorized agents.
•
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and the saw unit
is not at rest.
•
Make sure that the machine is always secu-
red on a workbench or a table if at all possi-
ble.
•
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of
a cut.
4. Additional instructions
•
Always pull the plug out of the power socket
before adjusting or servicing the machine.
•
Give these safety regulations to all persons
who work on the machine.
•
Do not use this saw to cut fire wood.
•
Caution! Hands and fingers may be injured on
the rotating saw blade.
Anl_TC_SM_2534_Dual_SPK8.indb 38 Anl_TC_SM_2534_Dual_SPK8.indb 38
GB
•
Before you use the machine for the first time,
check that the voltage marked on the
rating plate is the same as your mains volta-
ge.
•
If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw's power consumption. Mi-
nimum crosssection: 1.5 mm
•
If you use a cable reel, the complete cable
has to be pulled off the reel.
•
Never carry the saw by its cable.
•
Do not leave the saw in the rain and never
use it in damp or wet conditions.
•
Provide good lighting.
•
Never saw near combustible liquids or gases.
•
Wear suitable work clothes! Loose garments
or jewellery may become caught up in the
rotating saw blade.
•
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are
allowed to use the machine under supervisi-
on.
•
Keep children away from the machine when it
is connected to the power supply.
•
Check the power cable. Never use a faulty or
damaged power cable.
•
Keep your workplace clean of wood scrap
and any unnecessary objects.
•
Persons working on the machine should not
be distracted.
•
Note the direction of rotation of the motor and
saw blade.
•
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
•
Fit only blades which are well sharpened and
have no cracks or deformations.
•
The machine is to be operated only with tools
which conform with EN 847-1: 2003.
•
Faulty saw blades have to be replaced
immediately.
•
Never use saw blades which do not comply
with the data specified in this manual.
•
Make sure that the arrow on the saw blade
complies with the arrow marked on the
machine.
•
Make certain that the saw blade does not
touch the rotary table in any setting. To do so,
pull out the power plug and tilt the saw blade
by hand into the 45° position and the 90°
position. If necessary, re-adjust the saw head
as described in Section C/F.
•
It is imperative to make sure that all the
devices used to cover the saw blade are in
good working order.
- 38 -
.
2
15.03.16 12:07 15.03.16 12:07