Selecting The Direction Of Rotation - BLACK&DECKER KR800 Manual De Instrucciones

using any tool for prolonged periods ensure you take
regular breaks.
f Impairment of hearing.
f Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing
one tool with another. The declared vibration emission
value may also be used in a preliminary assessment of
exposure.
Warning! The vibration emission value during actual
use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The
vibration level may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation
of vibration exposure should consider, the actual
conditions of use and the way the tool is used, including
taking account of all parts of the operating cycle such
as the times when the tool is switched off and when it is
running idle in addition to the trigger time.
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ASSEMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
f Turn the grip counterclockwise until you can slide
the side handle (7) onto the front of the tool.
f Rotate the side handle into the desired position.
f Insert the depth stop (6) into the mounting hole
as shown.
f Set the drilling depth as described below.
f Tighten the side handle by turning the grip clockwise.
Setting the drilling depth (Fig. B)
f Slacken the side handle (7) by turning the grip
counterclockwise.
f Set the depth stop (6) to the desired position.
The maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end
of the depth stop.
f Tighten the side handle by turning the grip clockwise.
Keyed chuck (Fig. C)
f Open the chuck by turning the sleeve (10) counterclockwise.
f Insert the bit shaft (9) into the chuck.
f Insert the chuck key (11) into each hole (12) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f Open the chuck as far as possible.
f Remove the chuck retaining screw, located in
the chuck,by turning it clockwise using a screwdriver.
f Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f Remove the Allen key.
f Remove the chuck by turning it counterclockwise.
f To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the drilling mode
f For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the
f For drilling in steel, wood and plastics, set the
operating mode selector (4) to the

Selecting the direction of rotation

For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill
bit, use reverse (counterclockwise) rotation.
f To select forward rotation, push the forward/reverse
slider (3) to the left.
f To select reverse rotation, push the forward/reverse
slider to the right.
Warning! Never change the direction of rotation while
the motor is running.
Switching on and off
f To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far you
press the switch.
f For continuous operation, press the lock-on button
(2) and release the variable speed switch. This option
is available only at full speed or at any speed preset
ENGLISH • 15
position.
position.