Chicco oasys 2-3 Evo Fix Plus Instrucciones De Uso página 23

INSTALLING THE CHILD SEAT INSIDE THE
eat
VEHICLE WITHOUT THE CHILD INSIDE
est When the child is not travelling in the car, the
est: child car seat should be left secured by the ve-
ap- hicle three-point safety belt, or stowed away in
ber the car boot. An unsecured child car seat may
hild be a source of danger for the other passengers
he in the event of an accident or sudden braking.
HOW TO REMOVE THE CHILD FROM THE
na-
CHILD CAR SEAT
he Release the car belt buckle, accompanying the
of belt as it retracts.
REMOVAL OF THE CHILD CAR SEAT
or-
he WARNING! Remove the child from the child car
nd seat before removing it.
1. Release the car safety belt.
(Q) 2. U nthread the diagonal strap through the
en guide, accompanying it as it retracts.
If the rigid clasps have been used to fasten the
he car seat in place, they must now be released
he from the anchor points:
of 1. P ull the two red buttons on the rigid clasp re-
eat. lease system® towards you, release the clasps
nst from the corresponding Isofix anchor points
he on the car seat ( Fig. 23) so that the indicator
re- is completely red.
lts, 2. H old the lever up (O) as you push the rigid
cle clasps all the way into the base of the child
nd car seat, ( Fig. 24).
to
HOW TO REMOVE AND REINSTALL SAFE PAD
Oasys 23 FixPlus EVO is certified for use with
and without SAFE PAD (S).
des To remove SAFE PAD take off the rear cover (Fig.
he 25), unhook SAFE PAD (S) (Fig. 26) and remove
SAFE PAD (Fig. 27). When carrying out this oper-
om ation remember to correctly replace the elastic
in- band behind the backrest. (Fig.39)
e it To reinstall SAFE PAD carry out the above oper-
ed ations in reverse.
INSTALLING AND REMOVING THE CUP
HOLDER
ove
car The child car seat has 2 inserts, one on the
hild right and one on the left of the side of the seat
un- where you can fit the cup holder whenever
you like.
To install the cup holder:
1. I nsert the cup holder into the relative guide
( Fig. 28).
2. P ress the cup holder downwards until it
clicks into place ( Fig. 29).
WARNING! Do not place glass containers or
hot liquids on the cup holder as they could
harm the child.
To remove it:
1. P ress the lever on the back of the cup holder
and lift it upwards, out of the guide ( Fig. 30)
The cup holder guides are fitted with a spe-
cial device that makes sure it always remains
in a horizontal position.
To rotate and position the cup holder:
1. P ress the lever on the back and rotate it to
the desired position
ADJUSTING THE HEIGHT OF THE BACK
REST
The height of the headrest can be adjusted to
10 different positions to adapt the child car seat
to the height of the child.
Make sure the child's head is always well pro-
tected and the car diagonal safety belt is posi-
tioned properly on his shoulder.
When adjusting the height of the backrest,
check that the diagonal belt loop (B) is posi-
tioned at a maximum of 2 cm above the child's
shoulder ( Fig. 31).
To make the adjustment:
1. U se one hand to press the child car seat
backrest height adjuster lever (L) located on
the back of the headrest ( Fig. 32)
2. R aise/lower the backrest to adapt it to the
height of the child's shoulders ( Fig. 33)
3. R elease the lever checking that it has clicked
into the desired position.
ADJUSTING THE WIDTH OF THE BACK
REST
The width of the backrest can be adjusted to
adapt the child car seat to suit the physique of
the child.
Use the backrest width regulator wheel (K) lo-
cated above the headrest, to adjust the width:
1. R otating it counter clockwise will increase the
width of the backrest ( Fig. 34) while rotating
it clockwise will decrease the width ( Fig. 35).
23