Tabla de contenido
Publicidad
MANUAL PRESET FM RADIO STATIONS
3.
DURING RADIO MODE, WHEN DESIRED FREQUENCY IS FOUND, PRESS MODE BUTTON. THIS
PARTICULAR FREQUENCY WILL BE STORED IN THE UNIT.
4.
PRESS PRESET DOWN OR PRESET UP BUTTON TO SELECT DESIRED STATION.
NOTE: MIXIMUM STORAGE: 30 STATIONS FOR FM.
FM & FM-STEREO RECEPTION
PRESS "FM ST." BUTTON ON THE REMOTE CONTROL TO SELTECT FM MONO OR FM STEREO MODE.
WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO.
"ST" ICON LIGHT UP ON THE DISPLAY TO SHOW FM STEREO MODE IS RECEIVING.
HINTS FOR BETTER RECEPTION
FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RADIO ENCODING
9.
PRESS FUNCTION BUTTON TO SELECT RADIO MODE.
10. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)
11. PRESS THE REC BUTTON, THEN USB OR SD ICON WILL BE FLASHING.
12. PRESS SKIP UP
FOR ENCODING. THEN PRESS THE REC BUTTON AGAIN TO CONFIRM. AND THE SYSTEM IS STARTING
THE ENCODING MODE AFTER FEW SECONDSS.
13. IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.
14. THE "REC" WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
15. TO FINISH ENCODING, PRESS STOP
16. TO HEAR NEWLY ENCODED TRACK:
PRESS FUNCTION BUTTON TO SELECT USB OR SD MODE.
PRESS SKIP UP
TRACK.
THE NEWLY ENCODED TRACK IS ALWAYS STORED AS THE LAST TRACK IN USB/SD.
DURING PLAYBACK FROM USB OR SD, PRESS REC BUTTON TO SWITCH BETWEEN TRACKS
ENCODED BY THIS UNIT OR OTHER TRACKS STORED IN THE USB (OR SD) ORIGINALLY.
REMARK:-
-
THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLAYING TIME OF FM RADIO
-
THE RECORDING FORMAT IS PRESET AT – MP3
-
DURING FM & FM-STEREO RADIO ENCODING, RADIO FREQEUNCY IS FXIED AND CANNOT BE TUNED
PHONO & ENCODING
NOTED:
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE
-
ARM REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
10. PRESS FUNCTION BUTTON TO SELECT "PHON" ON DISPLAY.
11. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
12. PLACE THE RECORD ON THE PLATTER, USE THE 45 RPM ADAPTOR IF REQUIRED.
13. PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
AND THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO
ROTATE.
14. PUT DOWN THE LIFT LEVER TO DROP THE TONE ARM AND TOUCH THE RECORD
GENTLY. PHONO PLAYING STARTS NOW.
15. PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
NOW PLATTER WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE PLAYING,
THE USER NEEDS TO PUT DOWN THE LIFT LEVER.
16. ADJUST THE VOLUME TO THE DESIRED LEVEL.
17. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. PUSH THE LIFT LEVER
UPWARD TO RAISE THE TONE ARM AND MOVE IT TO THE ARM PARK, AND THEN PUT DOWN THE LIFT
LEVER.
18. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM PARK.
BUTTON OR SKIP DOWN
BUTTON OR REC BUTTON , "REC" WILL DISAPPEAR.
BUTTON OR SKIP DOWN
BUTTON TO SELECT DESIRED MODE (USB OR SD)
BUTTON TO SELECT THE NEWLY ENCODED
BIT RATE : 128 KBPS
ž‰‹ƒ
Publicidad
Tabla de contenido
