Preparing For Operation; Checking The Machine; Using The Machine; Modes Of Operation And Working Techniques - EMAK Oleo-Mac BCi 30 Manual De Uso

comply with safety requirements and for the correct
position of the string cutter.
Secure the guard (A) using the 2 screws (B) in a position
allowing the operator to work safely.

5. PREPARING FOR OPERATION

5.1 CHECKING THE MACHINE

WARNING! Make sure that the battery is not fitted in its
housing.
Before beginning work, it is necessary to:
- check that the switch lever and safety lever can move
freely, without forcing, and that upon release they return
quickly and automatically to their neutral position;
- check that the switch lever stays locked, if the safety lever
is not pressed;
- check that the cooling vents are not clogged;
- check that the handles and machine guards are clean and
dry, correctly assembled and firmly secured to the
machine;
- check that the cutting devices and guards are not
damaged;
- check that the machine has no signs of wear or damage
due to impact or other causes, and make the necessary
repairs;
- check that the battery is in good conditions and that there
are no signs of damage. Do not use the machine with a
damaged or worn battery;
- charge the battery following the instructions given in the
chapter "Charging the battery".
5.2 CHECKING THE STATUS OF THE BATTERY (Fig.3)
To check the battery (A) charge status, press button (B) which
activates 4 LEDs (C) which mean the following:
4 LED lights on = Duration = 4/4
3 LED lights on = Duration = 3/4
2 LED lights on = Duration >= 2/4
1 LED light on = Duration =< 1/4
1 Flashing LED light = battery is flat
4 Flashing LED lights = overheating
5.3 CHARGING THE BATTERY (fig.4)
CAUTION: Make sure that the mains voltage of the power
outlet corresponds to that indicated on the battery charger
label.
To remove the battery (A) from the machine, press the two
buttons (B) and slide the battery out (A).
To recharge battery:
- connect the battery charger (C) to a power outlet; the
presence of voltage is indicated by the red warning light
(D) switching on.
- insert the battery (A) into its housing in the battery charger
(C), pushing all the way. Recharging a completely flat
battery requires approx. 113 minutes (2.5 Ah) and 225
minutes (5 Ah).
The recharging stages are indicated by the warning light (D):
- connected battery charger = red warning light on.
- battery inserted and recharging in progress = green
warning light flashing.
- battery recharging completed = green warning light on.
- short circuit = red warning light flashing quickly
- overheating = red warning light flashing slowly
Recharging complete:
- remove the battery (A) from the battery charger (C) and
refit it on the machine;
- disconnect the battery charger (C) from the power outlet.

6. USING THE MACHINE

6.1 STARTING UP THE MACHINE (Fig.5)
Before starting up the machine, insert the battery (A) into its
housing.
To start up the machine:
- Firmly grip the machine with both hands.
- Press the safety lever (D) and operate the switch (C).
6.2 STOPPING THE MACHINE (Fig.5)
To stop the machine:
- Release the switch (C).
- Press the two buttons (B) to slide the battery out (A).

7. MODES OF OPERATION AND WORKING TECHNIQUES

WARNING! For your safety and the safety of others:
1) Remember that the operator or user is responsible for
accidents and unforeseen events that may occur to
other people or their property.
2) Wear appropriate clothing while working. Your dealer
can give you information on the most appropriate
accident prevention material to ensure workplace
safety.
3) Thoroughly inspect the entire work area and remove
anything that could be thrown by the machine or
damage the cutting device (stones, branches, wires,
bones, etc.).
4) Pay attention to the possible ejection of material by
the cutting device.
5) Stop the motor and remove the battery from its
housing:
- if the machine starts to vibrate abnormally: in this case,
immediately look for the cause of the vibration and
make the necessary checks at an Authorized Service
Center;
each time the machine is left unattended.
-
CAUTION: Always remember that an incorrectly used power
trimmer may be disruptive to others. To respect others and the
environment:
- Avoid using the machine in places and at times that may
be disruptive.
- Strictly comply with local regulations for the disposal of
waste materials after cutting.
GB
19