Minimum Clearances For Installation And Combustibility Of Construction Materials; Product Description - Sunsystem BURNIT Pell serie Operación Manual

TECHNICAL PASSPORT INSTALLATION and OPERATION MANUAL
DANGER of intoxication or explosion
Toxic gases may be discharged when
burning waste, plastics, liquids.
$
- Use only the fuels indicated in this manual.
- In case of danger of explosion, ignition or
discharge of exhaust gases in the room,
stop the pellet burner from operation.

Customer must undergo boiler operation/
maintenance
installer/service shop.
Safety rules for user operation:
- Operate the pellet burner on recommended fuel
only, and to that end you must regularly inspect the
boiler room.
- Do not use flammable liquids for ignition or increase
of burner output.
- Collect ash in lid-covered fireproof containers.
- Clean the burner surface using non-flammable
agents only.
- Do not place flammable objects onto the burner
housing and heating boiler cabinet or in their
proximity. (see diagram 1 for the minimum
clearances)
- Do not store flammable materials in the boiler room.
- Boilers, chimneys and other connections of mounted
burner must meet standards for fire and emergency
safety of the country.
- It is mandatory to strictly observe instructions for
connecting the burner to power network as well as
to all peripherals.
- Structural changes to burner by user can cause
damage to equipment or injury.
- Do not allow contact transmission of electrical wire
or touch any part of the boiler, where the surface
temperature can exceed 70°C.
- Dismount the burner when the boiler are heating
alternative (mainly) of fuel - wood, wood briquettes,
coal or other fuel.
- This manual should be kept throughout the lifetime
of the burner.
CAUTION! Hot surface!
Risk of burns if you touch the running
system. Burner housing, body and flange
are hot surfaces during burner operation.
;
It is strictly prohibited to open boiler
inspection doors with the burner running.
Also, exercise caution when touching the
observation port for monitoring the burning
process. It may be hot.
1.2.3. Minimum clearances for installation and
combustibility of construction materials
training by authorized
Diagram 1. Recommended clearances
between the boiler with mounted burner
and walls
The applicable minimum clearances in your country
may differ from the ones specified below. Please,
consult your installer.
The minimum distance from the burner, heating
boiler or exhaust gas pipe to objects or walls must be
at least 200 mm.
Table 1. Combustibility of construction materials
Stone, bricks, ceramic tiles, baked
Class А – non-
clay, solutions, plaster free of
combustible
organic additives.
Gypsum board panels, basalt fiber
needled felt, fiberglass board,
Class B – hard
combustible
AKUMIN, Izomin, Rajolit, Lignos,
Velox, Heraklit.
Class С1/С2 -
Wood beech, oak
Medium
Wood softwood, layered wood
combustible
Asphalt, cardboard, cellulose, tar,
Class C3 – easy
fiberboard, cork, polyurethane,
combustible
polyethylene.
For general safety considerations, we recommend
that the boiler be placed on a foundation with height
of 100 mm made of class A material, see table 1.

2. PRODUCT DESCRIPTION

The BURNiT Pell pellet burner for hot water boilers is
designed to burn only and exclusively wood pellets
and it is intended to heat up heating boilers. The
built-in control unit, automatic cleaning system and
internal pellet auger ensure the automated operation
of the burner and optimal burning of the fuel.
2.1. Design.
The burner is made of high-quality stainless steel
able to withstand temperatures of up to 1150°С. The
burner must be installed on a heating boiler.
The burner consists of two parts: combustion
chamber tube and external tube with sheet metal
mantle. Longitudinally, under the housing, there are
blow chamber, fuel ignition heater, fan and power
supply. On the upper part of the burner there is a
feeder chute to which the pellet auger is attached.
The housing of the burner has been designed to
meet all regulatory safety requirements (no sharp
or protruding elements) with operating temperature
not exceeding 50 °C.
5
EN