Functional Description And Specifications - Dremel MM45 Instrucciones De Funcionamiento

DM 2610030830 01-13_DM 2610030830 01-13.qxp 1/22/13 11:25 AM Page 7

Functional Description and Specifications

Disconnect the plug from the power source before making any
WARNING
!
assembly, adjustments or changing accessories. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Model MM45 Multi-Max™ Oscillating Power Tool
ON/OFF
SWITCH
™
QUICK LOCK
LEVER
CLAMPING
FLANGE
ACCESSORY
Model number
No load speed
Voltage rating
NOTE: For tool specifications refer to the nameplate on your tool.
FIG. 1
VARIABLE SPEED
CONTROL DIAL
POWER
CORD
VENTILATION
OPENINGS
VENTILATION
OPENINGS
ACCESSORY HOLDER
MM45
n 10,000-21,000/min
0
120 V 60 Hz
-7-
DV-2610030830, Page: MUL (VAA), downloaded at: 2013.03.08_20:02:07, by PT-RT/MKP2-DR_Saad.Alam
Assembly
Disconnect the plug from
WARNING
!
the power source before
making any assembly, adjustments or
changing accessories. Such preventive
safety measures reduce the risk of starting the
tool accidentally.
For all work or when
WARNING
!
changing accessories
always wear protective gloves. Such
preventive safety measures reduce the risk of
injury from sharp edges of the accessories.
Application tools can become very hot while
working. Danger of burns!
INSTALLING AND REMOVING
ACCESSORIES WITH QUICK LOCK™
ACCESSORY CHANGE
The Dremel Multi-Max™ MM45 includes an
integrated accessory change mechanism. The
Quick Lock™ accessory interface allows you to
install and remove accessories without the need
of a wrench or hex key. You will also no longer
need to worry about losing a clamping screw &
washer as these parts are no longer used in the
MM45 version of the Multi-Max™.
1. To install an accessory using the Quick
Lock™ feature, hold tool upside down to
prevent the blade from falling off the
accessory holder when installing and
removing accessories.
2. Turn the Quick Lock™ lever on the top on the
tool counter-clockwise to unlock the clamping
mechanism (Fig. 2). The lever needs to be
fully engaged to unlock the clamping
mechanism.
FIG. 2
OPEN
CLOSE
3. Clean accessory holder, accessory and the
clamping flange with a clean cloth.
4. Place the accessory onto the accessory
holder making sure the accessory engages
all pins in the holder and the accessory is
CLAMPING
FIG. 3a
FLANGE
ACCESSORY
HOLDER
FIG. 3b
flush against the accessory holder (Fig. 3a &
Fig 3b).
To avoid pinching, firmly
WARNING
!
hold Quick Lock lever when
fastening accessory. Avoid placing hands
or fingers between lever and tool body.
5. Turn the Quick Lock™ lever on the top of the
tool in a clockwise motion, to the closed
position, to securely lock the accessory in
place (Fig. 2).
6. To remove an accessory, simply unlock the
clamping mechanism by turning the Quick
Lock™ lever counter-clockwise as described
above (Fig. 2).
7. Lift up on the accessory bracket to take it off
the pins. (Note: be careful, blade may be
hot.)
NOTE: Some accessories, such as scrapers
or blades, may be mounted either straight
on the tool, or at an angle to increase
usability (Fig. 4). In order to do this with the
Quick Lock™ interface, place the accessory
onto the accessory holder making sure the
accessory engages all pins in the holder and
the accessory is flush against the accessory
holder. Securely lock the accessory in place
as described previously (Fig. 2).
-8-