EGO BCA1200 Manual De Usario página 8

◾
If you are approached, stop the motor and cutting
EN
attachment. In the case of bladed units, there is
the added risk of injury to bystanders from being
struck with the moving blade in the event of a
blade thrust or other unexpected reaction of the
blade.
◾
Warn the operator of the danger of blade thrust.
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade.
A dull blade is more likely to snag and thrust.
◾
A coasting blade can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade has completely stopped rotating.
◾
Do not charge the battery pack in rain, or in wet
locations.
◾
Use only with the battery packs and chargers listed
below:
BATTERY PACK
BA1120E, BA2240E, BA2800,
◾
The battery pack must be removed from the
appliance before it is scrapped.
◾
Do not dispose of the battery in a fire. The cells may
explode. Check with local codes for possible special
disposal instructions.
◾
Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
◾
Exercise care in handling batteries in order not
to short the battery with conducting materials
such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
8
BRUSH CUTTER ATTACHMENT — BCA1200
◾
Replacement Parts - When servicing, use only identical
EGO replacement parts. Use of any other accessory or
attachment may increase the risk of injury.
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Remove or disconnect battery pack before servicing,
cleaning or removing material from the brush cutter.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
◾
Save these instructions. Refer to them frequently
and use them to instruct others who may use this tool.
If you lend this tool to someone else, also lend these
instructions to them to prevent misuse of the product
and possible injury.
NOTE: SEE YOUR POWER HEAD OPERATOR'S
MANUAL FOR ADDITIONAL SPECIFIC SAFETY RULES.
SPECIFICATIONS
Cutting Width
No-Load Speed
Weight
Measured sound power level L
CHARGER
CH2100E
Sound pressure level at
CH5500E
operator's ear L
Guaranteed sound power level L
(measured according to 2000/14/EC)
Valuation of
vibration a
◾
The above parameters are tested and measured
equipped with power head PH1400E;
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾
The declared vibration total value may also be used in
a preliminary assessment of exposure.
30 cm
5000/6000 min
1.82 kg
96.5 dB(A)
K=1.88 dB(A)
WA
84.5 dB(A)
K=3 dB(A)
PA
98 dB(A)
WA
2.8 m/s
Front-assist handle
K=1.6 m/s
:
3.1 m/s
h
Rear handle
K=1.6 m/s
-1
2
2
2
2