Powers Fasteners P3500 Manual De Instrucciones página 4

MODEL P3500
determine the minimum threaded length,
add the thickness of the fixture and the nut
/ washer thickness. The nut and washer
thickness is equal to the nominal thread
diameter. Do not over tighten threaded
parts. Maximum tightening torque values
are listed in the table below. Use of a nut
setter is recommended to reduce the possibility of over tightening
the fasteners. For critical applications, perform a job site test.
MAXIMUM TORQUE
FOR 1/4" STUD (FT.-LBS.)
2
INSTALLATION IN STEEL
The following guidelines are based on the installation of a
fastener in ASTM A 36 structural steel with the point fully
penetrating the steel member. Recommended steel material
thickness ranges from a minimum of 1/8" to a maximum of
3/8". For use in higher strength structural steel, applications
where the point does not penetrate the steel member, or a
thickness of steel greater than 3/8", job site performance tests
are recommended.
BASE MATERIAL THICKNESS
Steel base materials should be a minimum of 1/8" in thickness.
EDGE DISTANCE
For installations in A 36 steel, 1/2" is the recommended
minimum edge distance.
SPACING
The recommended minimum distance between fastenings is
1-1/2" center to center for installations in ASTM A 36 steel.
FASTENER LENGTH SELECTION IN STEEL
For permanent applications when using pins in steel, first
determine the thickness of the
fixture to be fastened. To this, add the thickness of the steel
base material plus a minimum of 1/4" to allow for proper point
penetration. This will be the minimum fastener shank length
required. Do not select a fastener length longer than that
required for the application. An excessively
long shank can burnish or polish the hole
created in the steel resulting in a reduction
in load capacity.
For removable applications with
threaded studs, the shank length required is
equal to the thickness of the steel base
material plus a minimum of 1/4" to allow
for proper point penetration. This will be the
minimum fastener shank length required.
Do not select a shank length longer than
that required for the application. An
excessively long shank can burnish or polish
the hole created in the steel resulting in a reduction in load
capacity. To determine the minimum threaded length, add the
thickness of the fixture and the nut / washer thickness. The nut
and washer thickness is equal to the nominal thread diameter.
Do not over tighten threaded studs, the maximum tightening
torque is listed in the table below. Use of a nut setter is
recommended to reduce the possibility of over tightening the
fasteners. For critical applications, perform a job site test.nut and
washer thickness is equal to the nominal thread diameter.
P3500
4
@@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@ yyyyyy @@@@@@ @@@@@@
yyyyyy @@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@
Thread Length
@@@@@@ @@@@@@ yyyyyy @@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@
Embedment
@@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@ @@@@@@ yyyyyy
MAXIMUM TORQUE
FOR 3/8" STUD (FT.-LBS.)
4
1/8"
1/2"
1-1/2"
CAT. NO.52000/Deluxe Kit
Do not over tighten threaded studs, the maximum tightening
torque is listed in the table below. Use of a nut setter is
recommended to reduce the possibility of over tightening the
fasteners. For critical applications, perform a job site test.
Powder Load Selection Guide
.27 CALIBER SAFETY STRIP
CAT. POWER LOAD
NO. LEVEL COLOR SIZE
50620 2 Brown .27 strip
50622 3 Green .27 strip
50626 4 Yellow .27 strip
50630 5 Red .27 strip
.27 CALIBER SAFETY STRIP
CAT. POWER LOAD
NO. LEVEL COLOR SIZE
50624 3 Green .27 strip
50628 4 Yellow .27 strip
50632 5 Red .27 strip
Fastener Selection Guide
.300 HEAD DIAMETER DRIVE PINS
CAT. STD.
NO. SHANK LENGTH BOX
50012 1/2" K 100
50016 5/8" K 100
50022 3/4" 100
50026 1" 100
50030 1-1/8" 100
50032 1-1/4" 100
50034 1-1/2" 100
50036 1-3/4" 100
50038 2" 100
50040 2-1/4" 100
50042 2-3/8" 100
50044 2-1/2" 100
50046 2-3/4" 100
50048 3" 100
.300 HEAD DIAMETER DRIVE PINS WITH TOP HAT
CAT. STD.
NO. SHANK LENGTH BOX
50136 1/2" K 100
50138 5/8" K 100
50140 3/4" 100
50144 1" 100
.300 HEAD DIAMETER STEP SHANK PINS
CAT. STD.
NO. SHANK LENGTH BOX
50158 3/4" Step Shank 100
50159 1" Step Shank 100
.300 HEAD DIAMETER DRIVE PINS -MASTER PACK
CAT. STD.
NO. SHANK LENGTH BOX
50980 1/2" K 1000
53300 5/8" K 1000
51040 3/4" 1000
51100 1" 1000
51160 1-1/4" 1000
51340 1/2" K TH 1000
53400 5/8" K TH 1000
51400 3/4" TH 1000
51520 1" TH 1000
52001/Blister Pack
®
STD. STD. MASTER WT./
BOX CTN. CTN. 100
100 1000 20000 .33
100 1000 20000 .33
100 1000 20000 .33
100 1000 20000 .33
® MASTER PACK
STD. STD. MASTER WT./
BOX CTN. CTN. 100
1000 - 20000 .33
1000 - 20000 .33
1000 - 20000 .33
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .6
1000 .300 .143 .7
1000 .300 .143 .8
1000 .300 .143 .9
1000 .300 .143 1.1
1000 .300 .143 1.2
1000 .300 .143 1.2
1000 .300 .143 1.3
1000 .300 .143 1.4
1000 .300 .143 1.6
1000 .300 .143 1.9
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .6
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
1000 .300 .143/130 .5
1000 .300 .143/130 .6
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .6
5000 .300 .143 .8
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .6
K=Knurled TH=Top Hat
®