Rotary Hammer Safety Warnings; Standard Accessories; Optional Accessories (Sold Separately) - Hitachi Koki DH 38SS Instrucciones De Manejo

ROTARY HAMMER SAFETY WARNINGS

1. Wear ear protectors
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
SPECIFICATIONS
Voltage (by areas)*
Power input
Capacity
No load speed
Full-load impact rate
Weight (without cord, side handle)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Case (molded plastic) ..................................................1
(2) Side handle ..................................................................1
Standard accessories are subject to change without
notice.

OPTIONAL ACCESSORIES (sold separately)

○ Through-hole drilling (Rotation + Hammering)
(1) Drill bit (hexagon shank)
Overall length: 280, 400, 505 mm
External dia.: 16, 19, 22, 25, 28, 32, 38 mm
○ Anchor hole drilling (Rotation + Hammering)
(3) Cotter
(1) Drill bit (taper shank)
External dia.: 11, 12, 14.3,
14.5, 17.5,
21.5 mm
Taper shank
Application drill bit
adapter
Morse taper Drill bit (taper shank)
(No. 1) 11, 12, 14.3, 14.5, 17.5 mm
Morse taper Drill bit (taper shank)
(No. 2) 21.5 mm
Taper shank adapter formed A-taper
A-taper
or B-taper is provided as optional
accessory, but drill bit for it is not
B-taper
provided.
+
(2) Taper shank
adapter
4. Before starting to break, chip or drill into a wall, fl oor or
ceiling, thoroughly confi rm that such items as electric
cables or conduits are not buried inside.
5. Always hold the body handle and side handle of
the power tool fi rmly. Otherwise the counterforce
produced may result in inaccurate and even dangerous
operation.
6. Wear a dust mask
Do not inhale the harmful dusts generated in drilling or
chiseling operation. The dust can endanger the health
of yourself and bystanders.
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
950 W*
Drill bit: 38 mm
Core bit: 105 mm
620 /min
2800 /min
6.4 kg
○ Large dia. hole boring (Rotation + Hammering)
(1) Center (Guide
pin plate)
(1) Center pin
○ Applied to core bits from 38 mm to 105 mm
○ Applied to core bits 32 mm and 35 mm
NOTE
Do not use core bits 25 mm or 29 mm.
(2) Core bit
○ External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94,
105 mm
(with guide plate, not applicable to cores 25 mm or
29 mm)
(3) Core bit shank
○ Applied to core bits above 38 mm
○ Applied to core bits below 35 mm
○ Anchor work (for self-anchors)
(1) Anchor adapter (for Rotation + Hammering)
Anchor size:
W1/4, W5/16, W3/8, W1/2, W5/8
(No. 20) (No. 25) (No. 30) (No. 40) (No. 50)
○ Crushing (Hammering)
(1) Bull point
Overall length: 280, 450 mm
English
(2) Core (3) Core bit
bit shank
(2) Drift key
7