Controls And Functions - SYNQ X.TRM-1 Manual De Instrucciones

USER MANUAL

CONTROLS AND FUNCTIONS

1. START / STOP Button: Press this button to start or stop the platter.
2. STROBE DOTS: The dots around the edge of the platter are used in conjunction with
the light located inside the power switch. While the platter rotates, the dots help to
indicate the speed. The dots flow to the right when the platter speed is lower than the
selected (33, 45, 78. When the dots flow to the left, the platter speed is higher. When
the dots seem to be stationary, the platter is rotating at the exact speed. Use the Pitch
slider (12) to adjust the speed.
3. POWER ON/OFF SWITCH: Used to turn the turntable on an off.
4. SPEED SELECT Buttons: Used to select the desired speed.
• Press the "33" button to select the 33rpm speed.
• Press the "45" button to select the 45rpm speed.
• Press "33" and "45" buttons simultaneously to select the 78rpm speed.
5. TARGET LIGHT: White led target light used to locate the exact place on your record
when used in a dark place.
6. STARTUP TIME: Used to adjust the time it takes to reach the proper platter speed.
Startup time is minimal when the potentiometer is completely turned to the left. (proper
speed attained after 0.2sec) Startup time is maximum when the potentiometer is
completely turned to the right. (proper speed attained after 6sec)
7. BRAKE TIME: Used to adjust the time it takes to completely stop the platter. Break
time is minimal when the potentiometer is completely turned to the left. (complete stop
after 0.2sec) Break time is maximum when the potentiometer is completely turned to
the right. (complete stop after 6sec)
SYNQ®
V2.2 ENGLISH
3/30 X-TRM 1 TURNTABLE
USER MANUAL
8. REVERSE Button: Press this button to reverse the platter rotation, press this button
again to end the reverse mode.
9. PITCH RANGE +/-10% Button: Press this button to adjust the range of the pitch slider
to +/-10%. Used when precise speed adjustments are needed. (beat mixing)
10. PITCH RANGE +/-20% Button: Press this button to adjust the range of the pitch slider
to +/-20%. Press the +/-10% and +/-20% buttons simultaneously to adjust the range of
the pitch slider to +/-50%. Used to obtain special effects.
11. PITCH SLIDER & QUARTZ Button: Use the pitch slider to change the actual speed of
the platter. The Range depends on the Pitch Range buttons (9+10). When the slider is
in its middle position, a led will turn on to indicate that the turntable is locked to the
exact center speed. When the QUARTZ Button is pressed, the exact center speed is
enforced, even when the slider is not in the middle.
12. PHONO/LINE Output: Depending on the position of
the phono/line switch, you can connect the turntable
to any phono or line input, using the supplied
cinch/cinch cable. (a "cinch connector" is often also
called "RCA-connector")
13. POWER CORD Connector: Used to connect to the
mains, using the supplied power cord.
14. HEAD SHELL: Install the cartridge here. When installing a cartridge, refer to the
installation instructions supplied by the manufacturer of that cartridge. During
installation, attach the stylus protector to guard the stylus tip from damage.
Attach wires as follows:
White (L+) Left channel +
Blue (L-) Left channel -
Red (R+) Right channel +
Green (R-) Right channel -
15. HEAD SHELL LOCKING NUT: Attach the head
shell by inserting it into the front end of the tone
arm and then turn the locking nut clockwise.
16. TONE ARM: This is a fully manual S-shaped
tone arm. To start playback, gently place the
stylus on the record using the head shell finger
support. Do not drop the stylus onto the record
as this may cause damage to the diamond tip
and to the record.
17. TONE ARM LIFT: Used to adjust the height of
the tone arm. Put a vinyl record on the platter
and put the needle somewhere on the record.
Gently unlock the tone arm lift by turning a small
knob located on the tone arm base, next to the
ANTI SKATING knob for about 90° counter
clockwise. Turn the base ring clockwise to lift the
tone arm or counter clockwise to lower it until the
tone arm is horizontal. Relock the tone arm lift
again by turning the small knob for 90°
SYNQ®
V2.2 ENGLISH
4/30 X-TRM 1 TURNTABLE