Asist AE9BS09DN Instrucciones De Uso página 39

is again precisely fitted as shown in Fig. A or the brick
cover 2 will not fit.
Reattach the brick cover 2 and fasten in place with the
4 screws 3
CLEaNiNg aND maiNTENaNCE
This product is maintenance-free except for replacing
the bricks.
RISK OF ELECTRIC SHOCK! Unplug the
mains plug from the socket prior to performing mainte-
nance or repairs.
Clean the product regularly, preferably immediately
after every use.
Use a dry cloth to clean the housing. Never use petrol,
solvents or cleaning agents that attack plastic.
RISK OF INJURY! Never open the product except to
replace the brick. Always have repairs or parts repla-
cements performed at the service centre or by
an electrician. If the input lead on this product is da-
maged, it must be replaced with a specially prepared
power cord at the service centre.
Maintenance
• The equipment is maintenance free. Storage
• Store the appliance in a dry place well out of reach
of children.
• Grinding disks must be stored dry and upright and
are not to be stacked.
TECHNiCaL DaTa
power: 95W
Voltage: 230V / 50Hz
speed: 1600/ / min
For drill Ø: 3–12 mm
Protection class
Subject to changes.
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 61,2 dB (A) KpA=3
LWA (sound power) 74,2 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
<2,5 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
aE9BS09DN
II.
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVirONmENTaL PrOTECTiONWaSTE ma-
NagEmENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and its approximation
in national laws, unfit power tools must be handed
over at the point of purchase of similar equipment, or
in available collection points designated for collection
and disposal of power tools. Such disposed power
tools will be collected, disassembled and delivered for
environment-friendly recycling.
WarraNTY
In the attached material, you will find our warranty
conditions.
Date of manufacture
The date of manufacture is incorporated into the serial
number stated in the product nameplate.
The serial number has the format of ORD-YY-MM-
SERI, where ORD is the number of purchase order, YY
stands for the year of manufacture, MM is the month
of manufacture and SERI means the serial product
number.
39