Specifications; Product Specifications; Engine Specifications - Craftsman 580.752010 Instrucciones De Uso

ENGINE TECHNICAL INFORMATION
This is a single cylinder, L-head, air cooled engine. It
is a low emissions engine.
In the State of California, Model Series
100000 engines are certified by the California Air
Resources Board to meet emissions standards for
125 hours. Such certification does not grant the
purchaser, owner or operator of this engine any
additional warranties with respect to the performance
or operational life of this engine. The engine is
warranted solely according to the product and
emissions warranties stated elsewhere in this manual.
Power Ratings
The power ratings for an individual engine model are
initially developed by starting with SAE (Society of
Automotive Engineers) code J1940 (Small Engine
Power & Torque Rating Procedure) (Revision 2002-
05). Given both the wide array of products on which
our engines are placed, and the variety of
environmental issues applicable to operating the
equipment, it may be that the engine you have
purchased will not develop the rated horsepower when
used in a piece of power equipment (actual "on-site"
power). This difference is due to a variety of factors
including, but not limited to, the following: differences
in altitude, temperature, barometric pressure, humidity,
fuel, engine lubrication, maximum governed engine
speed, individual engine to engine variability, design of
the particular piece of power equipment, the manner in
which the engine is operated, engine run-in to reduce
friction and clean out of combustion chambers,
adjustments to the valves and carburetor, and other
factors. The power ratings may also be adjusted
based on comparisons to other similar engines utilized
in similar applications, and will therefore not
necessarily match the values derived using the
foregoing codes.

SPECIFICATIONS

PRODUCT SPECIFICATIONS

Pressure Washer Specifications
Pressure . . . . . . . . . . . . . . . . . . 2150 PSI
Flow Rate . . . . . . . . . . . . . . . . . 1.9 GPM
Chemical Mix. . . . . . . . . . . . . . . Use as directed
Water Supply Temperature . . . . Not to exceed 100°F
Shipping Weight . . . . . . . . . . . . 57 lbs.

Engine Specifications

Rated Horsepower . . . . . . . . . . . . 4.0 at 3600 rpm
Bore . . . . . . . . . . . . . . . . . . . . . . . 2.562 in. (65.09 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . 1.875 in. (47.63 mm)
Displacement . . . . . . . . . . . . . . . . 9.67 in. (158.6 cc)
Spark Plug
Type: . . . . . . . . . . . . . . . . . . . . . Champion RJ-19LM or
Set Gap To: . . . . . . . . . . . . . . . 0.030inch (0.76mm)
Armature Air Gap: . . . . . . . . . . . . 0.006-0.010 in.
Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold).
Intake . . . . . . . . . . . . . . . . . . . . . . 0.005-0.007 in.
Exhaust . . . . . . . . . . . . . . . . . . . . 0.007-0.009 in.
Fuel Capacity . . . . . . . . . . . . . . . . 1.0 Quarts
Oil Type:
Above 40° F . . . . . . . . . . . . . . . SAE 30
Below 40° F . . . . . . . . . . . . . . . SAE 5W-30 or 10W-30
NOTE: For practical operation, the horsepower
loading should not exceed 85% of rated horsepower.
Engine power will decrease 3-1/2% for each
1,000 feet (300 meters) above sea level and 1% for
each 10° F (5.6° C) above 77° F (25° C). It will
operate satisfactorily at an angle up to 15°.
12
Equivalent
(0.15-0.25mm)
(0.13-0.18 mm)
(0.18-0.23 mm)